I am reporting a premature oil pump failure on my 2020 BMW M340i xDrive with 42 thousand miles. The vehicle has been well maintained and has not experienced any oil pressure warning lights. However, the electronic engine oil level measurement repeatedly fails to complete once the engine is fully warmed up. I have also received stored BMW fault code 21B2C7 relating to engine oil pressure plausibility/excessive oil pressure. The fault currently shows as inactive, but it was not present previously. I have monitored engine oil pressure using diagnostic software. Pressure is generally around 38–42 psi at hot idle, approximately 44–48 psi during cruising, and can rise into the 60–78 psi range during acceleration. Although these readings are generally stable, the combination of the stored pressure plausibility fault and repeated inability to measure the engine oil level is concerning. I have also noticed a whining/humming noise from the front of the engine at low RPM, particularly during stop-and-go driving and while decelerating in first and second gear. There are numerous owner reports involving premature oil pump failures on BMW vehicles equipped with this generation of the B58 engine. The original oil pump used on earlier vehicles reportedly contains plastic internal components that can deteriorate over time and heat exposure. BMW later revised the oil pump design. BMW Korea has also reportedly begun providing repairs for certain B58 oil pump failures outside the normal warranty period while the issue is being investigated in that market. An engine oil pump is a critical lubrication component and is not a normal maintenance or wear item. Failure of the pump could result in insufficient or excessive oil pressure, loss of lubrication, severe engine damage, engine seizure, or loss of power while driving. I am submitting this complaint so NHTSA is aware of the potential pattern of premature oil pump failures affecting 2020 BMW M340i vehicles and
NHTSA complaint #11756783 — an unverified report by a vehicle owner.
Component Involved:Engine Mechanical / Variable-Displacement Engine Oil Pump (Part #11418635032 / Updated #11419895359) Description of Safety Hazard / Defect:The early-generation B58TU engine features a variable-displacement oil pump equipped with an internal thermoplastic (plastic) adjusting ring. Due to continuous thermal cycling and mechanical stress, this plastic ring is prone to cracking and shattering without warning.When this internal component disintegrates, it causes an immediate loss of oil pressure to critical engine components. This creates a severe safety hazard, as the vehicle can experience a sudden loss of motive power or complete engine seizure while travelling at highway speeds, placing the occupants and surrounding traffic at immediate risk of a collision.Furthermore, a known software bug or sensor interference tied to this specific mechanical failure prevents the iDrive system from successfully completing an electronic oil level measurement, thereby masking the impending failure from the driver until catastrophic engine failure occurs.Relevance of International Actions:In May 2026, BMW Korea officially acknowledged this identical component design flaw by launching a proactive, free preventative repair campaign for B58TU engines manufactured between January 2019 and June 2021. BMW is actively replacing the defective plastic-ring oil pumps with an updated, all-metal version in that market.North American consumers are driving vehicles equipped with the exact same defective part, manufactured during the same window, and facing the same catastrophic safety risks. I am requesting that the agency open a formal defect investigation into BMW North America to mandate a safety recall or an extended component warranty program.
NHTSA complaint #11754090 — an unverified report by a vehicle owner.
Safety Hazard: Oil Pump Failure Leading to Sudden Engine Stall (BMW B58TU engines) Description of Defect: The oil pump module in the 2020 BMW M340i (G20) and many other models between 2019-2020 contains internal plastic components that are prone to thermal degradation and premature failure. These plastic parts can crack or disintegrate, causing a sudden loss of oil pressure. BMW corrected this in later models with metal parts but failed to issue a recall or the older models containing plastic parts. Safety Risk: A failure of the oil pump leads to insufficient lubrication of critical engine components, which can result in a sudden and complete engine seizure while the vehicle is in motion. This causes an immediate loss of propulsion and power steering assist, significantly increasing the risk of a high-speed collision or being stranded in dangerous traffic conditions. Additional Note: This is a known mechanical defect where a critical engine component (oil pump) relies on non-durable plastic materials, creating an unreasonable safety risk for drivers and passengers due to potential catastrophic engine failure without prior warning.
NHTSA complaint #11750244 — an unverified report by a vehicle owner.
I am submitting this complaint regarding a potential safety defect involving the engine lubrication system on my 2020 BMW M340i with the B58 engine. The vehicle was purchased used from a single owner with low mileage and comprehensive maintenance records, with no indication of prior engine or lubrication issues. While traveling at highway speed, the vehicle suddenly displayed a low oil pressure warning and simultaneously entered a protective shutdown strategy, resulting in a significant loss of engine power. This forced me to rapidly slow down and merge across multiple lanes of traffic to reach the shoulder, creating a dangerous situation with a substantial risk of a rear-end or multi-vehicle collision. There were no warning lights, fault messages, drivability concerns, or other symptoms before this incident. According to the authorized BMW dealership that inspected the vehicle, the engine experienced an oil pump failure that caused a loss of oil pressure, resulting in internal engine damage. The dealership found metal shavings in the engine oil and recommended complete engine replacement rather than repairing the oil pump due to the extent of the damage. The vehicle and failed components are available for inspection upon request. Based on the dealership's diagnostic findings, there were no stored oil pressure fault codes prior to the failure; the only oil pressure warning occurred at the time the engine lost power. I am concerned that this indicates the vehicle did not provide meaningful advance warning before a catastrophic failure occurred. I believe this may represent a defect in the oil pump assembly that warrants investigation. I have seen many reports from other owners discussing failures involving the B58 oil pump assembly, including concerns about an internal plastic component that many owners proactively replace with an aftermarket metal component to reduce the risk of failure. This failure posed an incredible safety risk to me and others on the road.
NHTSA complaint #11748524 — an unverified report by a vehicle owner.
I have been smelling a burning odor in the vehicle for almost a year which the dealership and an independent shop had not been able to diagnose. The car was recently throwing Drivetrain Error codes which prompted a visit to the dealership. They found that the 48v battery and negative cable are burnt and quoted $5680 to replace the battery and cables. After investigating I found that there were recalls for this issue on other BMWs, including the same year and model of my vehicle, but my VIN is not pulling up a recall. The issue is a fire risk and a very expensive repair that should be covered by the manufacturer due to a known defect.
NHTSA complaint #11747887 — an unverified report by a vehicle owner.
The BMW B58TU oil pump thermoplastic component issue that can cause catastrophic failure to the engine. The the gen 1 oil pump was made from plastic and after issues were discovered, they switched to metal oil pumps. However this known issue is something that BMW has not addressed in the models 2019-2021 that came with the inferior oil pump.
NHTSA complaint #11747283 — an unverified report by a vehicle owner.
I am reporting a safety concern involving BMW vehicles equipped with the B58 Technical Update (B58TU) engine, commonly found in model years 2019–2021. These vehicles utilize a variable-displacement engine oil pump containing an internal thermoplastic adjusting component responsible for regulating oil pressure. Field failures are increasingly being reported in which this internal component fractures, resulting in sudden loss or instability of engine oil pressure. The failure frequently occurs during cold-start operation in low ambient temperatures. When the component fails, oil pressure regulation becomes erratic or is lost entirely. In many cases, drivers receive little or no actionable warning prior to engine damage or vehicle disablement. Reported precursor symptoms include inability to electronically measure engine oil level, abnormal oil pressure behavior, or sudden drivetrain malfunction warnings. Failures may rapidly progress to engine shutdown or severe mechanical damage caused by oil starvation. Loss of lubrication can cause the vehicle to become disabled without warning while driving or shortly after startup. This creates a safety hazard, particularly when vehicles become immobilized in active traffic or during winter conditions the cold is when they fail the most, where occupants may be exposed to freezing temperatures while awaiting assistance. Replacement of the oil pump requires extensive disassembly of the vehicle and repairs commonly exceed $6,000–$8,000 for just the pump, assuming the motor is unharmed. Failures have been reported across multiple production years, and affected vehicle population boundaries remain unclear. Because this condition can result in sudden vehicle disablement without adequate warning especially in the cold, I believe this issue warrants investigation as a potential safety-related defect.
NHTSA complaint #11740705 — an unverified report by a vehicle owner.
I am reporting a safety concern with BMW vehicles equipped with the B58 Technical Update (B58TU) engine, primarily in 2019–2021 model years. These vehicles use a variable-displacement oil pump containing an internal thermoplastic adjusting component that regulates oil pressure. This plastic part is prone to fracturing, leading to sudden loss or instability of engine oil pressure. Failures most commonly occur during cold starts in low ambient temperatures. When the component breaks, oil pressure regulation fails with little or no warning. Drivers often experience precursor symptoms such as inability to electronically read oil level, erratic oil pressure, or sudden drivetrain warnings. The issue can rapidly progress to engine shutdown or severe damage from oil starvation. This creates a serious safety hazard, as the vehicle can become disabled without warning while driving or shortly after startup — particularly dangerous in traffic or winter conditions when failures are most frequent, potentially stranding occupants in freezing temperatures. Oil pump replacement requires extensive disassembly and typically costs $6,000–$8,000 for the pump alone, assuming no further engine damage. Owners cannot reliably determine if their vehicle still has the original thermoplastic pump. VIN-based parts lookups now display the updated metal-component part number even when no replacement has occurred. BMW has also removed the original plastic part number from dealer systems, eliminating transparency. This issue affects multiple production years and continues to impact vehicles in the field
NHTSA complaint #11738024 — an unverified report by a vehicle owner.
Engine oil pump is failing. Early production 2019-2020 model years are made of plastic which can crack and break resulting in engine failure while driving. This is a well documented issue regarding the BMW B58 Engine (2nd Generation) They have since updated the engine oil pump part to a durable metal pump on newer models leaving the older ones with the bad part with no resolution. The vehicle no longer measures the oil level and is a symptom of the pump starting to fail. There is no telling when it may go out and it will be too late at that point as it results in complete engine failure/seizure while driving without proper pressure and lubrication. The local BMW Dealer says they are unable to help as BMW does not have a recall or technical service bulletin addressing this issue leaving owners with this plastic oil pump to pay out of pocket when this part fails destroying the motor. This is a critical safety hazard as the motor may shut off or malfunction at any given time while driving. The vehicle may produce a warning light or malfunction codes via the OBD, but at that point may be too late as the damage has already occurred. My independent bmw mechanic has also stated he sees many cars within this model year timeframe facing this issue as they age outside of the warranty period quoting $5K+ to ensure safety and fix this issue properly with the updated metal part. This is ridiculous as these cars by now are outside of the factory warranty period of 4 years and 50,000 miles. My vehicle does not measure the oil anymore even after a oil change leaving a big question mark of whether there is the proper amount of oil to lubricate the engine or not. I have attached pictures of the plastic oil pump showing cracks and breaks as well as the updated fully metal oil pump. There is no peace of mind when driving this vehicle due to this issue.
NHTSA complaint #11737366 — an unverified report by a vehicle owner.
Safety Hazard: Oil Pump Failure Leading to Sudden Engine Stall (BMW B58TU engines) Description of Defect: The oil pump module in the 2020 BMW M340i (G20) contains internal plastic components that are prone to thermal degradation and premature failure. These plastic parts can crack or disintegrate, causing a sudden loss of oil pressure. Increasing wear on internal engine components and even leading to irreversible engine damage. Safety Risk: A failure of the oil pump leads to insufficient lubrication of critical engine components, which can result in a sudden and complete engine seizure while the vehicle is in motion. This causes an immediate loss of propulsion and power steering assist, significantly increasing the risk of a high-speed collision or being stranded in dangerous traffic conditions. Additional Note: This is a known mechanical defect where a critical engine component (oil pump) relies on non-durable plastic materials, creating an unreasonable safety risk for drivers and passengers due to potential catastrophic engine failure without prior warning. BMW is aware of this defect as they chose to update the design in future models, switching from the brittle plastic to more metal components in the updated design. This shows clearly that this design is compromised and was a risk to continue implementing.
NHTSA complaint #11730475 — an unverified report by a vehicle owner.
I’ve been doing research for this particular issue on the 2020 bmw m340i (B58 engine). There is a plastic housing on the oil pump that seems to completely collapse due to consistent heat cycles (starting the vehicle). As far as I know that common symptoms include not being able to read oil levels and this is what commonly shows a faulty or unreliable oil pump that could potential cause a oil leak into engine where it gets hot and cause a fire. This is extremely dangerous and only the vehicles made from 2019-2020 have this plastic part that should be recalled from factory.
NHTSA complaint #11727385 — an unverified report by a vehicle owner.
Engine failed suddenly while driving on a highway. While driving at highway speed, warning lights and messages appeared indicating oil pressure is low and to turn off the engine immediately. The vehicle was towed to the shop where it was discovered that the oil pump, which was made out of plastic, had suffered a catastrophic failure. Was told if the engine continued running any longer it would have seized which could pose a very serious safety issue when at highway speeds. The vehicle had 55,000 miles at time of failure. Repairs totaled nearly $6,000 including towing and rental with a month of lost vehicle use. The failed oil pump was retained.
NHTSA complaint #11726317 — an unverified report by a vehicle owner.
I am reporting a safety concern involving BMW vehicles equipped with the B58 Technical Update (B58TU) engine, commonly found in model years 2019–2021. These vehicles utilize a variable-displacement engine oil pump containing an internal thermoplastic adjusting component responsible for regulating oil pressure. Field failures are increasingly being reported in which this internal component fractures, resulting in sudden loss or instability of engine oil pressure. The failure frequently occurs during cold-start operation in low ambient temperatures. When the component fails, oil pressure regulation becomes erratic or is lost entirely. In many cases, drivers receive little or no actionable warning prior to engine damage or vehicle disablement. Reported precursor symptoms include inability to electronically measure engine oil level, abnormal oil pressure behavior, or sudden drivetrain malfunction warnings. Failures may rapidly progress to engine shutdown or severe mechanical damage caused by oil starvation. Loss of lubrication can cause the vehicle to become disabled without warning while driving or shortly after startup. This creates a safety hazard, particularly when vehicles become immobilized in active traffic or during winter conditions the cold is when they fail the most, where occupants may be exposed to freezing temperatures while awaiting assistance. Replacement of the oil pump requires extensive disassembly of the vehicle and repairs commonly exceed $6,000–$8,000 for just the pump, assuming the motor is unharmed. Owners are currently unable to determine whether their vehicles contain the original thermoplastic oil pump design or a later revised version utilizing metal internal components, as VIN-based parts information now identifies updated components in the car even when no replacement has occurred and the old components are actually in the car. Also, BMW has actively removed the plastic part number out of all dealer networks as well.
NHTSA complaint #11725310 — an unverified report by a vehicle owner.
EXHIBITING SIGNS OF NOT BEING ABLE TO READ OIL LEVELS WHICH IS A POTENTIAL SIGN OF OIL PUMP FAILURE DUE TO PLASTIC INTERNAL COMPONENTS THAT HAS OCCURED IN 2020 MODELS.
NHTSA complaint #11724900 — an unverified report by a vehicle owner.
I am reporting a safety concern involving BMW vehicles equipped with the B58 Technical Update (B58TU) engine, commonly found in model years 2019–2021. These vehicles utilize a variable-displacement engine oil pump containing an internal thermoplastic adjusting component responsible for regulating oil pressure. Field failures are increasingly being reported in which this internal component fractures, resulting in sudden loss or instability of engine oil pressure. The failure frequently occurs during cold-start operation in low ambient temperatures. When the component fails, oil pressure regulation becomes erratic or is lost entirely. In many cases, drivers receive little or no actionable warning prior to engine damage or vehicle disablement. Reported precursor symptoms include inability to electronically measure engine oil level, abnormal oil pressure behavior, or sudden drivetrain malfunction warnings. Failures may rapidly progress to engine shutdown or severe mechanical damage caused by oil starvation. Loss of lubrication can cause the vehicle to become disabled without warning while driving or shortly after startup. This creates a safety hazard, particularly when vehicles become immobilized in active traffic or during winter conditions the cold is when they fail the most, where occupants may be exposed to freezing temperatures while awaiting assistance. As I waited for 4hr in -15c. Replacement of the oil pump requires extensive disassembly of the vehicle and repairs costed $8349 for just the pump, assuming the motor is unharmed. Owners are currently unable to determine whether their vehicles contain the original thermoplastic oil pump design or a later revised version utilizing metal internal components, as VIN-based parts information now identifies updated components in the car even when no replacement has occurred and the old components are actually in the car. Also, BMW has actively removed the plastic part number out of all dealer networks as well.
NHTSA complaint #11724191 — an unverified report by a vehicle owner.
I am reporting a safety concern involving BMW vehicles equipped with the B58 Technical Update (B58TU) engine, commonly found in model years 2019–2021. These vehicles utilize a variable-displacement engine oil pump containing an internal thermoplastic adjusting component responsible for regulating oil pressure. Field failures are increasingly being reported in which this internal component fractures, resulting in sudden loss or instability of engine oil pressure. The failure frequently occurs during cold-start operation in low ambient temperatures. When the component fails, oil pressure regulation becomes erratic or is lost entirely. In many cases, drivers receive little or no actionable warning prior to engine damage or vehicle disablement. Reported precursor symptoms include inability to electronically measure engine oil level, abnormal oil pressure behavior, or sudden drivetrain malfunction warnings. Failures may rapidly progress to engine shutdown or severe mechanical damage caused by oil starvation. Loss of lubrication can cause the vehicle to become disabled without warning while driving or shortly after startup. This creates a safety hazard, particularly when vehicles become immobilized in active traffic or during winter conditions the cold is when they fail the most, where occupants may be exposed to freezing temperatures while awaiting assistance. Replacement of the oil pump requires extensive disassembly of the vehicle and repairs commonly exceed $6,000–$8,000 for just the pump, assuming the motor is unharmed. Owners are currently unable to determine whether their vehicles contain the original thermoplastic oil pump design or a later revised version utilizing metal internal components, as VIN-based parts information now identifies updated components in the car even when no replacement has occurred and the old components are actually in the car. Also, BMW has actively removed the plastic part number out of all dealer networks as well.
NHTSA complaint #11721301 — an unverified report by a vehicle owner.
Oil pump in B58 BMW engines 2019-2022 has been a major safety concern that results in catastrophic failure while driving the vehicle. All because of BMW using a plastic component and quietly changed it, meanwhile hundreds of people had a major oil leak and engine seizures on hwy and $5k+ repairs.
NHTSA complaint #11721135 — an unverified report by a vehicle owner.
Oil pump is made of plastic causing it to fail after a certain time and can lead to a total engine loss if not swapped out with BMW’s updated oil pump. They are aware of the issue but neglecting to handle the problem.
NHTSA complaint #11721171 — an unverified report by a vehicle owner.