NHTSA has issued 10 recalls covering the Ford Bronco II. A recall repair is always free, however old the car is.
Check your own car by VIN
Recalls apply to specific build ranges, so a recall listed here may or may not cover your particular vehicle. NHTSA's free VIN lookup is the authority: nhtsa.gov/recalls.
EQUIPMENT DESCRIPTION: AFTERMARKET BRAKE ROTORS FOR USE ON CERTAIN FORD AND MAZDA TRUCKS. CRACKED CASTINGS CAUSED CRACKS TO APPEAR ON THE OUTER DIAMETER OF THE ROTOR HAT OR AROUND THE STUD HOLE.
Risk: LOSS OF BRAKING CAN RESULT.
Remedy: AIMCO WILL REIMBURSE CONSUMERS/INSTALLERS FOR THE COST OF REPLACEMENT ROTORS AND INSTALLATION. CONSUMERS ARE REQUESTED TO RETURN TO THE LOCATION WHERE THE ROTORS WERE ORIGINALLY PURCHASED/INSTALLED FOR REPLACEMENT.
WHEN THE AUTOMATIC TRANSMISSION SHIFT LEVER IS PLACED IN THE PARK POSITION, THE PARK PAWL DOES NOT ALWAYS ABUT OR ENGAGE THE PARK GEAR.
Risk: DRIVER MAY BELIEVE THE VEHICLE IS SAFELY ENGAGED IN PARKWHEN THE GEAR IS NOT TRULY ENGAGED. THIS CAN LEAD TO THE VEHICLE JUMPING OUT OFGEAR UNINTENTIONALLY, VEHICLE ROLLAWAY WHEN PARKED ON A SLOPED SURFACE, ANDINADVERTENT MOTION WHEN THE VEHICLE IS STARTED. ALL OF THESE CONDITIONS CANRESULT IN A VEHICLE ACCIDENT.
Remedy: REPAIR THE TRANSMISSION WITH A NEW PARK PAWL.
FRONT WHEEL BEARING ADJUSTING NUT RETAINING KEYS MAY BE MISSING FROM FRONT AXLE ASSEMBLIES, ALLOWING THE NUT TO LOOSEN.
Risk: THIS COULD RESULT IN DETACHMENT OF THE WHEEL AND HUBASSEMBLY FROM THE AXLE, LOSS OF VEHICLE CONTROL, AND AN ACCIDENT.
Remedy: INSTALL RETAINING KEYS IN FRONT WHEEL HUB ASSEMBLIES WHERE MISSING.
WIRING FOR THE POWER LUMBAR SEAT SYSTEM WAS ROUTED DIRECTLY BENEATH THE SEAT CUSHION SPRINGS AND MAY BE ABRADED BY THE SPRINGS.
Risk: THIS COULD RESULT IN A SHORT CIRCUIT WHICH MAY CREATESUFFICIENT HEAT TO START A FIRE IN THE SEAT CUSHION PAD AND/OR TRIM COVER.
Remedy: INSTALL A FUSE WITHIN THE POWER LUMBAR ELECTRICAL CIRCUIT.
SPRING LOCK FUEL LINE COUPLING MAY NOT BE PROPERLY ENGAGED.
Risk: COUPLING COULD DISENGAGE DUE TO FUEL PRESSURE,VIBRATION, AND ENGINE MOVEMENTS; THIS WOULD CAUSE LOSS OF FUEL WHICH, INPRESENCE OF AN IGNITION SOURCE, CREATES A FIRE RISK.
Remedy: INSTALL RETAINER CLIPS OVER THE COUPLINGS TO PREVENT COUPLING SEPARATION AND FUEL LEAKAGE.
SPRING LOCK FUEL LINE COUPLING MAY NOT BE PROPERLY ENGAGED.
Risk: COUPLING COULD DISENGAGE DUE TO FUEL PRESSURE,VIBRATION, AND ENGINE MOVEMENTS; THIS WOULD CAUSE LOSS OF FUEL WHICH, INPRESENCE OF AN IGNITION SOURCE, CREATES A FIRE RISK.
Remedy: INSTALL RETAINER CLIPS OVER THE COUPLINGS TO PREVENT COUPLING SEPARATION AND FUEL LEAKAGE.
STICKERS CONCERNING HANDLING AND MANEUVERABILITY WHICH ARE AFFIXED TO DRIVERS SUN VISOR SLEEVES DO NOT MEET CRITERIA FOR PERMANENT ADHESION.
Risk: VEHICLES DO NOT MEET FORMATS SPECIFIED BY PARTS 573 AND579 OF 49CFR.
Remedy: OWNERS WILL BE MAILED NEW SUN VISOR SLEEVES WITH ALL APPLICABLE DECAL INFORMATION PERMANENTLY AFFIXED.
ALUMINUM WHEELS MAY HAVE BEEN INSTALLED WITH IMPROPER LUG NUTS.
Risk: WHEEL COULD BECOME LOOSE OR EVEN SEPARATE FROM THE HUBAND AXLE ASSEMBLY WHILE THE VEHICE IS IN MOTION.
Remedy: CHANGE TAPERED STYLE LUG NUTS TO SHORT SHANK STYLE LUG NUTS.
NYLON FUEL LINES ON THE FUEL RETURN SIDE OF THE FUEL PRESSURE REGULATOR ASSEMBLY MAY CRACK. CONSEQUENCE OF DEFECT: FUEL LINE COULD LEAK AND, IF AN IGNITION SOURCE IS PRESENT, CREATE THE POTENTIAL FOR A FIRE.
Remedy: REPLACE NYLON FUEL HOSES WITH RUBBER HOSES.
THE ELECTRONIC ENGINE CONTROL WIRING HARNESS INSULATION MAY BE DAMAGED DUE TO COPPER SPIKES PRODUCED DURING THE WELDING OF ITS WIRES. THIS CREATES A POTENTIAL FOR A SHORT CIRCUIT BETWEEN THE WIRES WHICH ENERGIZE THE FUEL PUMP, CAUSING SOME FUEL INJECTORS TO OPEN, DISCHARGING FUEL INTO THE ENGINE. CONSEQUENCE OF DEFECT: FUEL DISCHARGED INTO THE ENGINE WOULD EVENTUALLY LEAK THROUGH THE EXHAUST SYSTEM TO THE GROUND. THIS COULD RESULT IN A FIRE IF A SOURCE OF IGNITION IS PRESENT.
Remedy: REPAIR WIRING HARNESS, CHECK ENGINE AND CATALYST FOR DAMAGE.
Transport Canada runs its own recall programme. Its campaigns do not always mirror the American ones, so a Canadian owner reading a US-only list is reading about a different car than the one on their driveway.
A SHORT CIRCUIT COULD DEVELOP IN THE IGNITION SWITCH THAT COULD LEAD TO OVERHEATING, SMOKE, AND POSSIBLY FIRE IN THE STEERING COLUMN OF THE VEHICLE. THIS CONDITION MAY OCCUR WHILE THE VEHICLE IS IN USE OR UNATTENDED. CORRECTION: IGNITION SWITCH WILL BE REPLACED WITH A REVISED DESIGN SWITCH.
A SHORT CIRCUIT COULD DEVELOP IN THE IGNITION SWITCH THAT COULD LEAD TO OVERHEATING, SMOKE, AND POSSIBLY FIRE IN THE STEERING COLUMN OF THE VEHICLE. THIS CONDITION MAY OCCUR WHILE THE VEHICLE IS IN USE OR UNATTENDED. CORRECTION: IGNITION SWITCH WILL BE REPLACED WITH A REVISED DESIGN SWITCH.
A SHORT CIRCUIT COULD DEVELOP IN THE IGNITION SWITCH THAT COULD LEAD TO OVERHEATING, SMOKE, AND POSSIBLY FIRE IN THE STEERING COLUMN OF THE VEHICLE. THIS CONDITION MAY OCCUR WHILE THE VEHICLE IS IN USE OR UNATTENDED. CORRECTION: IGNITION SWITCH WILL BE REPLACED WITH A REVISED DESIGN SWITCH.
A SHORT CIRCUIT COULD DEVELOP IN THE IGNITION SWITCH THAT COULD LEAD TO OVERHEATING, SMOKE, AND POSSIBLY FIRE IN THE STEERING COLUMN OF THE VEHICLE. THIS CONDITION MAY OCCUR WHILE THE VEHICLE IS IN USE OR UNATTENDED. CORRECTION: IGNITION SWITCH WILL BE REPLACED WITH A REVISED DESIGN SWITCH.
A SHORT CIRCUIT COULD DEVELOP IN THE IGNITION SWITCH THAT COULD LEAD TO OVERHEATING, SMOKE, AND POSSIBLY FIRE IN THE STEERING COLUMN OF THE VEHICLE. THIS CONDITION MAY OCCUR WHILE THE VEHICLE IS IN USE OR UNATTENDED. CORRECTION: IGNITION SWITCH WILL BE REPLACED WITH A REVISED DESIGN SWITCH.
THESE VEHICLES DO NOT COMPLY WITH C.M.V.S.S. 1103 - EXHAUST EMISSIONS. NITROUS OXIDE LEVELS EXCEED THE STANDARD. CORRECTION: OWNERS WILL BE PROVIDED WITH REVISED STARTING INSTRUCTIONS FOR THE OWNER GUIDE. CERTAIN VEHICLES WILL HAVE THE ENGINE EMISSIONS CONTROL SYSTEMS MODIFIED AND EXHAUST SYSTEM CATALYSTS REPLACED.
NOTE: ALSO INCLUDES SOME MEDIUM AND HEAVY TRUCKS. THESE VEHICLES MAY NOT COMPLY WITH C.M.V.S.S. 108 - LIGHTING. DAYTIME RUNNING LIGHT MODULE MAY MALFUNCTION WHICH CAN RESULT IN DAYTIME RUNNING LIGHTS THAT DIM, FLICKER OR GO OFF OR IN SOME INSTANCES MAY REMAIN ON AFTER THE IGNITION IS TURNED OFF. CORRECTION: DAYTIME RUNNING LIGHT MODULE WILL BE REPLACED ON AFFECTED VEHICLES.
THE PARK MECHANISM OF THE A4LD AUTOMATIC TRANSMISSION MAY NOT ENGAGE WHEN THE SELECTOR LEVER IS PLACED IN THE "PARK" POSITION. IF PARKED ON AN INCLINE, THE VEHICLE MAY ROLL AS IF IN NEUTRAL IF THE PARKING BRAKE IS NOT SET. THIS COULD RESULT IN A VEHICLE ACCIDENT OR PERSONAL INJURY. CORRECTION: OWNERS WILL BE NOTIFIED OF CONDITION AND ADVISED TO SET THE PARKING BRAKE EACH TIME THEY PARK THEIR VEHICLE. OWNERS WILL ALSO BE ADVISED WHEN DEALERS RECEIVE PARTS AND REPAIR INSTRUCTIONS AFTER FURTHER INVESTIGATION BY FORD.
THIS RECALL SUPERSEDES RECALL 90-27 FOR VEHICLES IN THE MARITIMES. THE THROTTLE MAY STICK IN AN OPEN POSITION DUE TO LINKAGE BINDING CAUSED BY CORROSION. THIS WOULD CAUSE THE ENGINE TO RUN AT HIGHER THAN IDLE SPEED WHEN THE THROTTLE IS RELEASED AND COULD ADVERSELY AFFECT DRIVER CONTROL RESULTING IN A POSSIBLE CRASH. CORRECTION: A STAINLESS STEEL SLEEVE, WHICH WILL BE PLACED OVER THE HUB ON THE THROTTLE BODY ASSEMBLY, AND A SECONDARY THROTTLE LEVER TO FIT THE SLEEVE, ALONG WITH OTHER MOUNTING PARTS, WILL BE INSTALLED ON AFFECTED VEHICLES.
THIS RECALL SUPERSEDES RECALL 90-27 FOR VEHICLES IN THE MARITIMES. THE THROTTLE MAY STICK IN AN OPEN POSITION DUE TO LINKAGE BINDING CAUSED BY CORROSION. THIS WOULD CAUSE THE ENGINE TO RUN AT HIGHER THAN IDLE SPEED WHEN THE THROTTLE IS RELEASED AND COULD ADVERSELY AFFECT DRIVER CONTROL RESULTING IN A POSSIBLE CRASH. CORRECTION: A STAINLESS STEEL SLEEVE, WHICH WILL BE PLACED OVER THE HUB ON THE THROTTLE BODY ASSEMBLY, AND A SECONDARY THROTTLE LEVER TO FIT THE SLEEVE, ALONG WITH OTHER MOUNTING PARTS, WILL BE INSTALLED ON AFFECTED VEHICLES.
THIS RECALL SUPERSEDES RECALL 90-27 FOR VEHICLES IN THE MARITIMES. THE THROTTLE MAY STICK IN AN OPEN POSITION DUE TO LINKAGE BINDING CAUSED BY CORROSION. THIS WOULD CAUSE THE ENGINE TO RUN AT HIGHER THAN IDLE SPEED WHEN THE THROTTLE IS RELEASED AND COULD ADVERSELY AFFECT DRIVER CONTROL RESULTING IN A POSSIBLE CRASH. CORRECTION: A STAINLESS STEEL SLEEVE, WHICH WILL BE PLACED OVER THE HUB ON THE THROTTLE BODY ASSEMBLY, AND A SECONDARY THROTTLE LEVER TO FIT THE SLEEVE, ALONG WITH OTHER MOUNTING PARTS, WILL BE INSTALLED ON AFFECTED VEHICLES.
RANGER/BRONCO II - 2.9 LITRE ENGINES TAURUS/SABLE - 3.0 LITRE ENGINES NOTE: VEHICLES LOCATED IN NEWFOUNDLAND, NOVA SCOTIA, NEW BRUNSWICK AND PRINCE EDWARD ISLAND. THE THROTTLE MAY STICK IN AN OPEN POSITION DUE TO LINKAGE BINDING CAUSED BY CORROSION. THIS WOULD CAUSE THE ENGINE TO RUN AT HIGHER THAN IDLE SPEED WHEN THE THROTTLE IS RELEASED AND COULD ADVERSELY AFFECT DRIVER CONTROL RESULTING IN A POSSIBLE CRASH. CORRECTION: ON VEHICLES WITH 2.9 LITRE ENGINES, DEALERS WILL CLEAN, MODIFY AND LUBRICATE THE HUB PIN AND LEVER BUSHINGS WITH A MARINE-TYPE ANTI-SEIZE GREASE. ADDITIONALLY, ON VEHICLES WITH 3.0 LITRE ENGINES, THE HUB PIN LEVER ASSEMBLY WILL BE REPLACED. NOTE: THIS RECALL HAS BEEN SUPERSEDED BY RECALL NO. 91021.
RANGER/BRONCO II - 2.9 LITRE ENGINES TAURUS/SABLE - 3.0 LITRE ENGINES NOTE: VEHICLES LOCATED IN NEWFOUNDLAND, NOVA SCOTIA, NEW BRUNSWICK AND PRINCE EDWARD ISLAND. THE THROTTLE MAY STICK IN AN OPEN POSITION DUE TO LINKAGE BINDING CAUSED BY CORROSION. THIS WOULD CAUSE THE ENGINE TO RUN AT HIGHER THAN IDLE SPEED WHEN THE THROTTLE IS RELEASED AND COULD ADVERSELY AFFECT DRIVER CONTROL RESULTING IN A POSSIBLE CRASH. CORRECTION: ON VEHICLES WITH 2.9 LITRE ENGINES, DEALERS WILL CLEAN, MODIFY AND LUBRICATE THE HUB PIN AND LEVER BUSHINGS WITH A MARINE-TYPE ANTI-SEIZE GREASE. ADDITIONALLY, ON VEHICLES WITH 3.0 LITRE ENGINES, THE HUB PIN LEVER ASSEMBLY WILL BE REPLACED. NOTE: THIS RECALL HAS BEEN SUPERSEDED BY RECALL NO. 91021.
RANGER/BRONCO II - 2.9 LITRE ENGINES TAURUS/SABLE - 3.0 LITRE ENGINES NOTE: VEHICLES LOCATED IN NEWFOUNDLAND, NOVA SCOTIA, NEW BRUNSWICK AND PRINCE EDWARD ISLAND. THE THROTTLE MAY STICK IN AN OPEN POSITION DUE TO LINKAGE BINDING CAUSED BY CORROSION. THIS WOULD CAUSE THE ENGINE TO RUN AT HIGHER THAN IDLE SPEED WHEN THE THROTTLE IS RELEASED AND COULD ADVERSELY AFFECT DRIVER CONTROL RESULTING IN A POSSIBLE CRASH. CORRECTION: ON VEHICLES WITH 2.9 LITRE ENGINES, DEALERS WILL CLEAN, MODIFY AND LUBRICATE THE HUB PIN AND LEVER BUSHINGS WITH A MARINE-TYPE ANTI-SEIZE GREASE. ADDITIONALLY, ON VEHICLES WITH 3.0 LITRE ENGINES, THE HUB PIN LEVER ASSEMBLY WILL BE REPLACED. NOTE: THIS RECALL HAS BEEN SUPERSEDED BY RECALL NO. 91021.
ON 4X4 VEHICLES, THE FRONT WHEEL BEARING ADJUSTING NUT RETAINING KEYS MAY HAVE BEEN OMITTED. IF THE KEY IS MISSING, THE LEFT FRONT WHEEL BEARING NUT MAY LOOSEN. THIS COULD LEAD TO WHEEL BEARING NOISE AND POSSIBLE DETACHMENT OF THE WHEEL AND HUB ASSEMBLY FROM THE AXLE AND COULD RESULT IN LOSS OF VEHICLE CONTROL. CORRECTION: LEFT FRONT WHEEL HUB ASSEMBLIES WILL BE INSPECTED AND MISSING RETAINING KEYS WILL BE INSTALLED IF NECESSARY.
On certain vehicles, wiring for the power lumbar seat system was routed directly beneath the seat cushion springs on the side of the cushion. This could result in the insulation being abraded by the seat springs resulting in a possible short circuit with the potential for a fire in the cushion pad or trim cover. Correction: Power lumbar seat wiring will be modified and a 15 amp fuse will be added to the wiring under the seat on Aerostars. On Bronco II and Ranger Super Cab vehicles the 30 amp circuit breaker, located in the fuse panel, will be replaced with a 15 amp fuse.
ON VEHICLES WITH EFI OR CFI, THE SPRING-LOCK FUEL LINE COUPLING USED TO CONNECT THE FUEL SUPPLY AND RETURN LINES TO THE EFI FUEL RAILS OR TO THE CFI THROTTLE BODIES AS WELL AS OTHER FUEL LINE CONNECTIONS NEAR THE DASH PANELS ON SOME VEHICLES, COULD DISENGAGE DURING VEHICLE USE. SHOULD THIS OCCUR, LOSS OF FUEL WILL RESULT, PROVIDING THE POTENTIAL FOR A VEHICLE FIRE. CORRECTION: COUPLING RETAINER CLIPS WILL BE INSTALLED ON AFFECTED VEHICLES. NOTE: ESCORT VEHICLES ARE EQUIPPED WITH EFI AND CFI. LYNX VEHICLES ARE EQUIPPED WITH CFI ONLY. EFI - ELECTRONIC FUEL INJECTION CFI - CENTRAL FUEL INJECTION
ON VEHICLES WITH EFI OR CFI, THE SPRING-LOCK FUEL LINE COUPLING USED TO CONNECT THE FUEL SUPPLY AND RETURN LINES TO THE EFI FUEL RAILS OR TO THE CFI THROTTLE BODIES AS WELL AS OTHER FUEL LINE CONNECTIONS NEAR THE DASH PANELS ON SOME VEHICLES, COULD DISENGAGE DURING VEHICLE USE. SHOULD THIS OCCUR, LOSS OF FUEL WILL RESULT, PROVIDING THE POTENTIAL FOR A VEHICLE FIRE. CORRECTION: COUPLING RETAINER CLIPS WILL BE INSTALLED ON AFFECTED VEHICLES. NOTE: ESCORT VEHICLES ARE EQUIPPED WITH EFI AND CFI. LYNX VEHICLES ARE EQUIPPED WITH CFI ONLY. EFI - ELECTRONIC FUEL INJECTION CFI - CENTRAL FUEL INJECTION
VEHICLES EQUIPPED WITH 2.9 LITRE E.F.I.,V6 ENGINES, THERE IS A POSSIBILITY THAT A NYLON FUEL LINE ON THE FUEL RETURN SIDE OF THE FUEL PRESSURE REGULATOR ASSEMBLY MAY CRACK AND LEAK FUEL. IN THE PRESENCE OF AN IGNITION SOURCE, THE POTENTIAL FOR FIRE WOULD EXIST.
ON VEHICLES WITH FRONT-DRIVE AUTOMATIC LOCKING HUBS THE CAM IN THE FRONT HUB LOCKING MECHANISM MAY BE INCORRECTLY HEAT TREATED. THE CAM COULD FRACTURE UPON ENGAGEMENT OF THE FRONT DRIVE AXLES. IF A PIECE OF THE CAM BECAME EMBEDDED IN THE WHEEL HUB NUT IT COULD CAUSE THE NUT TO LOOSEN AND EVENTUALLY RESULT IN WHEEL SEPARATION AND POSSIBLE VEHICLE CRASH.
THE UPPER TORSO RESTRAINT D-RING WHICH ATTACHES THE SHOULDER BELT TO THE B PILLAR, UNDER CERTAIN TEST CONDITIONS, SEPARATED FROM ITS ANCHORAGE, AND MAY NOT COMPLY WITH CMVSS 210 - BELT ANCHORAGE.
Source: Transport Canada Vehicle Recalls Database.