No recall records have been loaded for the Chevrolet C Series yet.
Check your own car by VIN
Recalls apply to specific build ranges, so a recall listed here may or may not cover your particular vehicle. NHTSA's free VIN lookup is the authority: nhtsa.gov/recalls.
Transport Canada runs its own recall programme. Its campaigns do not always mirror the American ones, so a Canadian owner reading a US-only list is reading about a different car than the one on their driveway.
On certain vehicles, a short in the electric outside rearview mirror switch could develop. If this were to occur, it could result in an inoperative switch, heat damage to the driver's door, and/or ignition of components in the driver's door and a subsequent vehicle fire without prior warning. Correction: Dealer will install a fused jumper harness to the electric outside rearview mirror switch.
On certain vehicles operated in areas of high salt use, the spare tire hoist cable may corrode and eventually break. This would allow the spare tire to fall off the vehicle possibly resulting in a road hazard for other vehicles. Correction: A letter will be sent to owners of affected vehicles with maintenance and inspection instructions for spare tire hoist cable assemblies. Additionally, the letter will advise the owner that, if the cable breaks during that inspection, their dealer will repair the assembly. This policy will be in effect until December 31, 2002.
On certain vehicles operated in areas of high salt use, the spare tire hoist cable may corrode and eventually break. This would allow the spare tire to fall off the vehicle possibly resulting in a road hazard for other vehicles. Correction: A letter will be sent to owners of affected vehicles with maintenance and inspection instructions for spare tire hoist cable assemblies. Additionally, the letter will advise the owner that, if the cable breaks during that inspection, their dealer will repair the assembly. This policy will be in effect until December 31, 2002.
On certain vehicles operated in areas of high salt use, the spare tire hoist cable may corrode and eventually break. This would allow the spare tire to fall off the vehicle possibly resulting in a road hazard for other vehicles. Correction: A letter will be sent to owners of affected vehicles with maintenance and inspection instructions for spare tire hoist cable assemblies. Additionally, the letter will advise the owner that, if the cable breaks during that inspection, their dealer will repair the assembly. This policy will be in effect until December 31, 2002.
On certain vehicles operated in areas of high salt use, the spare tire hoist cable may corrode and eventually break. This would allow the spare tire to fall off the vehicle possibly resulting in a road hazard for other vehicles. Correction: A letter will be sent to owners of affected vehicles with maintenance and inspection instructions for spare tire hoist cable assemblies. Additionally, the letter will advise the owner that, if the cable breaks during that inspection, their dealer will repair the assembly. This policy will be in effect until December 31, 2002.
On certain vehicles operated in areas of high salt use, the spare tire hoist cable may corrode and eventually break. This would allow the spare tire to fall off the vehicle possibly resulting in a road hazard for other vehicles. Correction: A letter will be sent to owners of affected vehicles with maintenance and inspection instructions for spare tire hoist cable assemblies. Additionally, the letter will advise the owner that, if the cable breaks during that inspection, their dealer will repair the assembly. This policy will be in effect until December 31, 2002.
On certain vehicles operated in areas of high salt use, the spare tire hoist cable may corrode and eventually break. This would allow the spare tire to fall off the vehicle possibly resulting in a road hazard for other vehicles. Correction: A letter will be sent to owners of affected vehicles with maintenance and inspection instructions for spare tire hoist cable assemblies. Additionally, the letter will advise the owner that, if the cable breaks during that inspection, their dealer will repair the assembly. This policy will be in effect until December 31, 2002.
On certain vehicles operated in areas of high salt use, the spare tire hoist cable may corrode and eventually break. This would allow the spare tire to fall off the vehicle possibly resulting in a road hazard for other vehicles. Correction: A letter will be sent to owners of affected vehicles with maintenance and inspection instructions for spare tire hoist cable assemblies. Additionally, the letter will advise the owner that, if the cable breaks during that inspection, their dealer will repair the assembly. This policy will be in effect until December 31, 2002.
Certain extended cab pickup trucks equipped with high-back bucket seats may have the seat recliner to seat frame attaching bolts loosen, fatigue and fracture, allowing the seat back to suddenly recline. If this were to occur on the driver's seat while the vehicle was in motion, it could lead to sudden loss of vehicle control and a crash without prior warning. Correction: Dealers will remove all foam and/or fabric sandwiched between the recliner assembly and the seat frame, install washers between the seat recliner and the seat frame at each attachment point, and install new attaching bolts torqued to a higher specification.
Certain vehicles were built with the polarity of the wiring for the zero adjust brake switch reversed from what was specified. Reversed polarity will cause the contacts of the switch to wear out prematurely. When the contacts wear out they will fail to close when the brake pedal is applied, resulting in the loss of the brake lamps without any warning to the driver. This could result in failure to warn a following driver that the vehicle is braking and could lead to a crash. Correction: Dealers will replace the brake switch and reverse the wiring.
On certain C1500, TAhoe and Yukon vehicles, the rear brake front pipe may contact the the left front fender wheelhouse inner panel just above the chassis frame. This could eventually wear a hole in the brake pipe which would result in brake fluid loss and reduced braking effectiveness. Correction: Rear brake pipe positioning clip will be relocated, brake pipe will be inspected for wear and replaced if necessary.
On certain crew cab pick ups, the front inner corner of the fuel tank may contact the body sill and over time wear a hole in or crack the fuel tank at the point of contact. This condition could result in fuel leakage and in the presence of an ignition source, a fire could occur. Correction: Tank will be inspected for wear and a spacer will be installed between the fuel tank and the front crossmember, or if necessary, the fuel tank will be replaced.
On certain crew cab pick ups, the front inner corner of the fuel tank may contact the body sill and over time wear a hole in or crack the fuel tank at the point of contact. This condition could result in fuel leakage and in the presence of an ignition source, a fire could occur. Correction: Tank will be inspected for wear and a spacer will be installed between the fuel tank and the front crossmember, or if necessary, the fuel tank will be replaced.
On certain crew cab pick ups, the front inner corner of the fuel tank may contact the body sill and over time wear a hole in or crack the fuel tank at the point of contact. This condition could result in fuel leakage and in the presence of an ignition source, a fire could occur. Correction: Tank will be inspected for wear and a spacer will be installed between the fuel tank and the front crossmember, or if necessary, the fuel tank will be replaced.
On certain crew cab pick ups, the front inner corner of the fuel tank may contact the body sill and over time wear a hole in or crack the fuel tank at the point of contact. This condition could result in fuel leakage and in the presence of an ignition source, a fire could occur. Correction: Tank will be inspected for wear and a spacer will be installed between the fuel tank and the front crossmember, or if necessary, the fuel tank will be replaced.
Certain vehicles may have windshield wiper motors with solder joints near the wiring harness connector that could crack. This could cause the windshield wiper to work intermittently and ultimately result in inoperative wipers. This could reduce driver visibility in inclement weather and result in a crash. Correction: Wiper motor circuit board and cover will be replaced.
Certain vehicles may have windshield wiper motors with solder joints near the wiring harness connector that could crack. This could cause the windshield wiper to work intermittently and ultimately result in inoperative wipers. This could reduce driver visibility in inclement weather and result in a crash. Correction: Wiper motor circuit board and cover will be replaced.
Certain vehicles may have windshield wiper motors with solder joints near the wiring harness connector that could crack. This could cause the windshield wiper to work intermittently and ultimately result in inoperative wipers. This could reduce driver visibility in inclement weather and result in a crash. Correction: Wiper motor circuit board and cover will be replaced.
Certain vehicles do not comply with CMVSS 1103 - Exhaust Emissions. Vehicles may been built with the ignition coil wire too close to metal brackets or the transmission fluid fill tube (M/L van only). If the coil wire is too close to these metal objects, arcing may occur and cause failure of the wires which can in turn lead to a stalling/no start condition and/or catalytic converter failures. Correction: coil wire will be repositioned to assure adequate clearance from metal brackets and/or transmission fluid fill tubes.
Certain vehicles do not comply with CMVSS 1103 - Exhaust Emissions. Vehicles may been built with the ignition coil wire too close to metal brackets or the transmission fluid fill tube (M/L van only). If the coil wire is too close to these metal objects, arcing may occur and cause failure of the wires which can in turn lead to a stalling/no start condition and/or catalytic converter failures. Correction: coil wire will be repositioned to assure adequate clearance from metal brackets and/or transmission fluid fill tubes.
Certain vehicles do not comply with CMVSS 1103 - Exhaust Emissions. Vehicles may been built with the ignition coil wire too close to metal brackets or the transmission fluid fill tube (M/L van only). If the coil wire is too close to these metal objects, arcing may occur and cause failure of the wires which can in turn lead to a stalling/no start condition and/or catalytic converter failures. Correction: coil wire will be repositioned to assure adequate clearance from metal brackets and/or transmission fluid fill tubes.
On certain C1500 and G1 vehicles, either one or both front brake rotor hubs may have out of specification grey iron that could fatigue during the life of the vehicle resulting in stress cracks which could propagate around the wheel mounting bolt circle. This could in turn result in wheel separation and a vehicle crash without prior warning. Correction: Rotors will be inspected and replaced if necessary.
Certain vehicles may not comply with CMVSS 207 - Seat Anchorages. Vehicles may have been shipped with one or two front seat mounting bolts not installed. In a vehicle crash, a seat with this condition will not protect the occupant as required by the standard. Correction: Dealers will check all seat mounting bolts and install new bolts where required.
On certain vehicles, the lower steering shaft to steering gear pinch bolt may be "finger loose" or missing. A "finger loose" bolt could continue to loosen and fall out. With the bolt missing, the steering shaft yoke could wear and jump spines on the steering gear shaft causing an off centre steering wheel. Relative movement between the chassis and cab could cause the steering shaft to separate from the steering gear resulting in loss of steering control. Correction: Dealers will inspect for the presence of a pinch bolt and ensure it is torqued to specification.
Certain vehicles exhibit a condition in which a pinch bolt exists in the recliner mechanism that could trap and pinch a person's hand or finger(s) when the easy entry feature is activated. This pinching could cut the hand or possibly sever the finger(s) without prior warning. Correction: a protector will be installed over the recliner mechanism.
Certain vehicles exhibit a condition in which a pinch bolt exists in the recliner mechanism that could trap and pinch a person's hand or finger(s) when the easy entry feature is activated. This pinching could cut the hand or possibly sever the finger(s) without prior warning. Correction: a protector will be installed over the recliner mechanism.
Certain vehicles exhibit a condition in which a pinch bolt exists in the recliner mechanism that could trap and pinch a person's hand or finger(s) when the easy entry feature is activated. This pinching could cut the hand or possibly sever the finger(s) without prior warning. Correction: a protector will be installed over the recliner mechanism.
Certain vehicles do not comply with CMVSS 1101 - Emissions. Vehicles were built with an incorrect emission control label. The label incorrectly identifies the engine family name. Correction: Correct labels and instructions for installation will be mailed to owners.
On certain vehicles, the crankshaft balancer centre attaching bolt was under-torqued. This bolt secures the balancer, which is pressed onto the crankshaft, and the accessory drive pulley which is attached to the balancer, to the engine crankshaft. If this bolt were to loosen, the balancer and drive belt pulley would eventually loosen and the drive belt could come off the pulley or break, causing a loss of drive to engine accessories such as the alternator and power steering pump. Correction: Crankshaft balancer centre bolt will be torqued to specification.
Certain vehicles may have a bead damage to the tires which occurred during tire mounting. The damage to the tire reinforcing structure in the bead "toe" area would likely manifest itself as a bulge in the sidewall after the tire is inflated. This damage could result in rapid air loss, which could cause injuries to anyone if they were handling the tire when this occurred. Correction: Tires will be demounted and inspected for bead damage. If bead damage is present, the tire will be replaced.
Certain vehicles may have a bead damage to the tires which occurred during tire mounting. The damage to the tire reinforcing structure in the bead "toe" area would likely manifest itself as a bulge in the sidewall after the tire is inflated. This damage could result in rapid air loss, which could cause injuries to anyone if they were handling the tire when this occurred. Correction: Tires will be demounted and inspected for bead damage. If bead damage is present, the tire will be replaced.
On certain vehicles, the four u-bolt nuts on either side of the rear axle may be under torqued. This could cause the bolts to loosen and eventually fall off the u-bolt. Should this occur, the axle would eventually be free to provide steering inputs to the vehicle and a crash could occur. Correction: Dealers will check the u-bolt nut torque and torque any loose u-bolts to specification.
Certain vehicles may not comply with CMVSS 124 - Accelerator Control Systems. Vehicles may have been assembled with the throttle cable contacting the dash mat. The dash mat may bind the throttle cable such that the throttle return time may not meet the requirements of the standard. Correction: Dealers will inspect for adequate throttle cable to dash mat clearance, and if there is insufficient clearance, a portion of the dash mat will be cut out to provide clearance.
Certain vehicles may not comply with CMVSS 124 - Accelerator Control Systems. Vehicles may have been assembled with the throttle cable contacting the dash mat. The dash mat may bind the throttle cable such that the throttle return time may not meet the requirements of the standard. Correction: Dealers will inspect for adequate throttle cable to dash mat clearance, and if there is insufficient clearance, a portion of the dash mat will be cut out to provide clearance.
On certain vehicles, the seat recliner to seat frame attaching bolts could loosen, fatigue and fracture, allowing the seat back to suddenly recline. If this were to occur to the driver's seat, sudden loss of vehicle control could result with the possibility of a crash without prior warning. Correction: Washers will be installed between the seat recliner and the seat frame at each attachment point and new attaching bolts will be installed and torqued to a higher specification. These corrections will be performed on both the driver's and passenger's seat.
On certain vehicles, the seat recliner to seat frame attaching bolts could loosen, fatigue and fracture, allowing the seat back to suddenly recline. If this were to occur to the driver's seat, sudden loss of vehicle control could result with the possibility of a crash without prior warning. Correction: Washers will be installed between the seat recliner and the seat frame at each attachment point and new attaching bolts will be installed and torqued to a higher specification. These corrections will be performed on both the driver's and passenger's seat.
On certain vehicles, the steering column upper intermediate shaft nut may not be torqued to the proper specification. The nut could detach allowing the through bolt that secures the upper intermediate shaft to the lower steering column shaft to fall out. This could result in possible shaft separation, loss of steering control and a vehicle crash. Correction: Suspect fasteners will be torqued to specification.
Certain vehicles may experience a fuel leak at the fuel rail assembly end plug due to an improperly crimped end retainer clip. If this condition were to occur, and an ignition source was present, an engine compartment fire could occur. Correction: Defective fuel rail assemblies will be replaced.
On certain vehicles, the transmission shift cable lock clip may back out of its installed position resulting in loss of cable adjustment. This could cause the transmission to not obtain mechanical PARK when the shift lever is placed in the PARK position. If the driver fails to apply the parking brake, unwanted vehicle movement could occur. Correction: The shift cable will be adjusted and a redundant lock clip will be installed.
On certain vehicles, the service-part fuel tanks may have one or more pairs of the six projection welds which attach the sender-unit ring to the tank that do not meet specification. These out of specification welds may fracture during sender unit installation resulting in fuel leakage and a possible vehicle fire. Note: recall covers 1975-1986 chevrolet/gmc c/k pickup and chassis cab trucks and 1987-1991 chevrolet/gmc r/v pickup and chassis cab trucks. Correction: vehicles with fractured sender ring weld pairs will have a new fuel tank installed.
On certain vehicles, the left-hand lower control arm to frame rear nut was inadequately torqued. This may allow the attachment bolt to loosen and subsequently fatigue and break. Bolt breakage could result in separation of the left-hand lower control arm from the frame causing loss of vehicle control and a crash without prior warning. Correction: The left-hand lower control arm to frame rear nut will be tightened to the proper torque specification.
On certain vehicles, each side of the weight-distribution trailer hitch was attached by just two of the three specified fasteners. This could allow the hitch to move under towing loads and result in eventual failure of the fasteners. If this were to occur while a trailer was being pulled, the hitch and trailer could separate from the vehicle and a crash could occur without prior warning. Correction: Dealers will install a bolt, two washers, and a nut on each side of the trailer hitch platform.
Certain vehicles do not comply with CMVSS 207 - Anchorage of Seats. Vehicles may be missing bolts that connect the upper slave hinge to the seat back frame or bolts that connect the seat to the seat adjuster. Correction: Vehicles will be inspected and bolts installed if required.
Certain crew cab pick ups do not comply with CMVSS 207 - Anchorage of Seats. Rear bench seat latch mechanism was riveted to the back frame lower cross tube instead of bolted as specified and thus will not meet the requirements of the standard. Correction: Rivets will be replaced with the required bolts.
Certain vehicles were built with a brake pedal push rod retainer missing, mispositioned or not properly seated. This condition could cause the stop lamp switch and the brake booster push rod to disconnect from the brake pedal, resulting in loss of brake operation and a possible vehicle crash. Correction: Vehicles will be inspected to ensure the brake pedal retainer is secure and fully seated in the groove and can be rotated a full 360 degrees in both directions.
On certain vehicles, the transmission fluid may be forced out of the vent tube due to heat generation in the transmission caused by trailering heavy loads at high speeds or high-load/off road use. If the vented transmission fluid comes in contact with the catalytic converter, the fluid could ignite resulting in a vehicle fire. Correction: Dealers will install a longer transmission vent hose routed to the left side of the vehicle.
On certain vehicles, the transmission fluid may be forced out of the vent tube due to heat generation in the transmission caused by trailering heavy loads at high speeds or high-load/off road use. If the vented transmission fluid comes in contact with the catalytic converter, the fluid could ignite resulting in a vehicle fire. Correction: Dealers will install a longer transmission vent hose routed to the left side of the vehicle.
On certain vehicles, the transmission fluid may be forced out of the vent tube due to heat generation in the transmission caused by trailering heavy loads at high speeds or high-load/off road use. If the vented transmission fluid comes in contact with the catalytic converter, the fluid could ignite resulting in a vehicle fire. Correction: Dealers will install a longer transmission vent hose routed to the left side of the vehicle.
On certain vehicles, the transmission fluid may be forced out of the vent tube due to heat generation in the transmission caused by trailering heavy loads at high speeds or high-load/off road use. If the vented transmission fluid comes in contact with the catalytic converter, the fluid could ignite resulting in a vehicle fire. Correction: Dealers will install a longer transmission vent hose routed to the left side of the vehicle.
On certain vehicles, the transmission fluid may be forced out of the vent tube due to heat generation in the transmission caused by trailering heavy loads at high speeds or high-load/off road use. If the vented transmission fluid comes in contact with the catalytic converter, the fluid could ignite resulting in a vehicle fire. Correction: Dealers will install a longer transmission vent hose routed to the left side of the vehicle.
Certain vehicles may develop an abnormal pressure build-up in the transmission with the possibility of transmission fluid coming out of the filler tube onto hot engine parts resulting in a possible vehicle fire. Correction: Owners will be provided with a new dipstick with a lock-seal top and new owner manual instructions and graphics for checking the automatic transmission fluid level.
Certain vehicles may develop an abnormal pressure build-up in the transmission with the possibility of transmission fluid coming out of the filler tube onto hot engine parts resulting in a possible vehicle fire. Correction: Owners will be provided with a new dipstick with a lock-seal top and new owner manual instructions and graphics for checking the automatic transmission fluid level.
Certain vehicles may develop an abnormal pressure build-up in the transmission with the possibility of transmission fluid coming out of the filler tube onto hot engine parts resulting in a possible vehicle fire. Correction: Owners will be provided with a new dipstick with a lock-seal top and new owner manual instructions and graphics for checking the automatic transmission fluid level.
Certain vehicles may develop an abnormal pressure build-up in the transmission with the possibility of transmission fluid coming out of the filler tube onto hot engine parts resulting in a possible vehicle fire. Correction: Owners will be provided with a new dipstick with a lock-seal top and new owner manual instructions and graphics for checking the automatic transmission fluid level.
On certain C3500HD vehicles, the tie rod may fracture through the damper stud mounting hole. Under moderate to heavy braking or significant power steering pump inputs, the wheel can pull out and slide resulting in a pulling to the left. This could result in a vehicle crash without prior warning. Correction: Tie rod assembly, damper and damper bracket will be replaced with newly designed parts.
Certain vehicles do not comply with CMVSS 209 - Seatbelt Assemblies. Incorrect instructions for rear seat lap-shoulder belts. Correction: Owners manuals will be revised.
Certain vehicles do not comply with CMVSS 209 - Seatbelt Assemblies. Incorrect instructions for rear seat lap-shoulder belts. Correction: Owners manuals will be revised.
On certain vehicles, the pivot bolt, which holds the brake pedal to its support bracket, could disengage from the bracket weld nut resulting in loss of braking action. This could result in a vehicle crash without prior warning. Correction: Brake pedal pivot bolts will be torqued to specificaiton.
Certain C10 pickup trucks do not comply with CMVSS 1101 - Emission Device. - incorrect emission label -
On certain vehicles with diesel engines, the front fuel feed and/or return lines can contact the automatic transmission shift linkage cordon shaft and/or, on k models, the front propshaft. The fuel line could wear through allowing diesel fuel to leak near the exhaust crossover pipe possibly resulting in an engine compartment fire. Correction: A newly designed fuel line routing bracket will be installed. Additionally, the fuel lines will be inspected for wear and if necessary, replaced.
Source: Transport Canada Vehicle Recalls Database.