65 of the
488 complaints filed about the Toyota Grand Highlander
are about the transmission —
100% of everything owners reported.
The worst model year for it is 2024.
65
Complaints
100%
Share of all complaints
1
Crashes
0
Fires
Transmission & Drivetrain complaints by model year
2024 Toyota Grand Highlander XLE FWD. At approximately 38,000 miles I began hearing a roaring/humming noise that varied with vehicle speed. The condition initially progressed slowly but then became much worse within several days. At 41,510 miles a Toyota dealer diagnosed and replaced the right rear hub/wheel bearing assembly. I was advised that the failed bearing was nearly seized when removed. After replacement the noise was reduced but remained present. The dealer was uncertain whether another bearing was failing and initially believed the remaining noise could be tire noise, advising me to monitor it. The noise again deteriorated rapidly and became severe enough that I considered the vehicle unsafe to drive. At 42,223 miles the same dealer diagnosed and replaced the left rear hub/wheel bearing assembly. The noise disappeared after replacement. Both rear wheel bearings therefore failed at approximately 40,000–42,000 miles within about 700 miles of each other. The vehicle has no known accident or suspension damage and the dealer identified no other condition causing the failures. I am concerned that rapid deterioration or seizure of a wheel bearing while driving could result in loss of vehicle control.
NHTSA complaint #11762946 — an unverified report by a vehicle owner.
When ambient temperature are over ~90 the vehicle will lose power during acceleration. This happens typically in the speed range of ~20-35mph. The vehicle’s rpm will spike high but lose the ability to increase speed or shift gears. This occurs ~ 40-50% of the time when over 90 degrees. On several occasions we were forced to abandon merging onto the highway because the vehicle wasn’t safely able to accelerate to match the speed of vehicles on the highway. We reported this issue to our local Toyota dealer September 2025. After reviewing the vehicle they said nothing was wrong. We had them drive it longer and they agreed the vehicle had these issues. The dealership spoke with Toyota and they confirmed there was an issue for our vehicle and a lot of others and they had no fix for it. That was September 30, 2025; Toyota Brand Engagement Center Reference # 250923001413. There has been no communication from Toyota or our dealer since then. The safety issue with the vehicle is a major concern in operation of the vehicle and with the hot climate we live in, is putting our occupants and others on the road at risk and we feel Toyota needs to be held accountable for finding the issue(s) and correcting them.
NHTSA complaint #11762145 — an unverified report by a vehicle owner.
After starting the vehicle and coming to a conplete stop the vehicle will hesitate upon new acceleration. The hesitation causes a lag in the vehicle and it then will jerk or jolt while shifting. The vehicle will Rev up in a low gear and not shift correctly. This causes a safety issue especially when going into traffic. I have not taken it to the dealer as of yet, but I will be. This is an intermittent issue, so i fear toyota will say they cannot replicate the issue. There were no warning lamps when the event happens.
NHTSA complaint #11762019 — an unverified report by a vehicle owner.
At 5:16 pm, CST. I was stopped at a stop sign headed west on a 25 mph road crossing a 30 mph road (that does not have a stop sign) in Illinois. After waiting for a an appropriate gap in traffic, I attempted to accelerate though the interesting. I released the brake pedal and attempted to accelerate. The vehicle barely accelerated. The engine seemed to minimally climb in RPM and only accelerated minimally out into the cross road. This lasted approximately 1-2 seconds. AT this point I was fully into the first lane of traffic. I then fully depressed the accelerator to try to get the vehicle to respond and after approximately a 0.5 to 1.0 second delay the engine fully responded and I was able to accelerate out of the oncoming cross traffic. This is by no-means the first time this behavior has happened with this vehicle but it is the first time I'm reporting it to the NHTSA.
NHTSA complaint #11761276 — an unverified report by a vehicle owner.
Sometimes, when trying to accelerate in certain situations, the vehicle accelerator pedal will not respond or the engine stutters and won't immediately respond to input and the vehicle seems to stall. This has been scary several times in traffic. The vehicle originally would throw an engine code on the dash about system failure and was taken into the dealer after several of these incidents and a software updates was performed, but it still happens randomly although now with no code.
NHTSA complaint #11759560 — an unverified report by a vehicle owner.
I continuously have issues accelerating from stop in my max hybrid. the issue is particularly worse when it is warm out. I press the gas and the RPMs drop really low and I barely move through the intersection for a few seconds. Once it finally registers after a number of seconds, the RPMs rev up over 4000. It is very dangerous trying to proceed through an intersection and the car basically stalls when I press the gas. It especially concerns me that I have my child in the car with me and I worry when it is going to act up. I know others have experienced this issue and there was a TSB for 2024 models that had this issue. I have a 2025 and experience this issue. I have had toyota look at it and they said they cant do the TSB since it's bot for my VIN. A solution needs to be found for the the safety of myself and others.
NHTSA complaint #11759592 — an unverified report by a vehicle owner.
The contact owns a 2024 Toyota Grand Highlander. The contact stated that while making a right turn from a complete stop to merge into traffic, the vehicle hesitated and failed to exceed 7–10 MPH. The contact released and then depressed the accelerator pedal again, and the vehicle responded as intended. No warning light was illuminated. The vehicle was taken to the dealer, where software updates were performed on several occasions; however, the failures persisted. The vehicle was not repaired. The manufacturer was notified of the failure, but no assistance was provided. The failure mileage was approximately 800.
NHTSA complaint #11759021 — an unverified report by a vehicle owner.
Vehicle intermittently fails to accelerate when accelerator pedal is depressed after stopping. Vehicle may move extremely slowly for several seconds and then suddenly regain power. This has occurred while entering/intersecting traffic and has resulted in near-collision situations. Dealer cannot duplicate the problem.
NHTSA complaint #11756305 — an unverified report by a vehicle owner.
My vehicle has a recurrent issue with failing front axle assemblies. The vehicle experienced rotational clicking and had both from axle assemblies replaced around 20,000 miles. Around 40,000 miles the clicking returned and toyota has refused to replace the failing axles again. I currently am at 63,000 miles and I won an arbitration case regarding the axles. The arbitration decision ordered toyota to replace the axles and determined that the parts were defective and covered under warranty. Toyota breached the arbitration and refused to replace the defective axles as ordered in a legally binding arbitration. Rotational clicking is more apparent at low ambient temperatures. A metallic grinding is more apparent at high ambient temperatures. I have had several drive train skips, a sensation of drive train parts slipping and slamming together. Toyota knowingly put defective parts back on my car during the 20,000 mile repair. Toyota release a technical service bulletin T-SB-0082-24 in sep of 2024. It stated that they redesigned the axle to fix the problem. The tsb said to put the original part number on instead of the updated, fixed part number. I received the old, broken part number when my repair was done in 2025. There is a new bulletin T-SB-0028-26 release in april 2026 for the same issue and it states that the previous bulletin is obsolete. The new bulletin states that the correct part number is the new part number not the old one. Additionally, the tsb indicates toyota changed to the new part number with a vin cutoff sometime in 2024. The fixed part number was changed at the production line level in 2024 yet I received the old, known defective part. These are drive axles and a failure can lead to loss of control and a serious accident. A full investigation and recall of this part should be conducted.
NHTSA complaint #11754520 — an unverified report by a vehicle owner.
The contact owns a 2024 Toyota Grand Highlander. The contact stated that while driving at an undisclosed speed and turning the steering wheel to the left or the right, occasionally there was a clicking sound coming from the vehicle. The dealer was contacted and diagnosed the failure as an axle failure. The vehicle was repaired, but the failure reoccurred approximately two to three months later. The vehicle was repaired five times due to failures. There was no sound coming from the vehicle after the last repair. The manufacturer was not made aware of the failure. The failure mileage was approximately 5.
NHTSA complaint #11753270 — an unverified report by a vehicle owner.
I own a 2024 Toyota Grand Highlander Platinum Hybrid MAX with approximately 34,000 miles. The vehicle has experienced repeated delayed or absent acceleration from a complete stop, creating a serious risk when entering traffic. Before the most recent repair, I reported intermittent hesitation to the Toyota dealer. On Sunday, July 12, 2026, shortly after startup, the vehicle hesitated twice within the first half mile. At the second stop sign, I attempted a left turn into traffic and applied approximately 30% accelerator pedal. The engine was running, but the vehicle only crept forward at idle-level power for approximately three seconds. There was no noticeable increase in engine RPM and no warning lights. Normal power then returned. On July 15, 2026, the Toyota dealer performed TSB T-SB-0017-24 and updated the engine-control software for hesitation during acceleration. After that repair, the same loss-of-acceleration condition happened again while my wife was leaving a parking lot. She was stopped at a stop sign, making a right turn into traffic on a slight uphill grade, when the vehicle failed to provide normal acceleration. This was substantially similar to the earlier incident and occurred after the software update intended to correct the problem. The repeated failure to respond to accelerator input from a stop creates a collision risk because the vehicle can begin entering traffic without providing the expected power. I am requesting that NHTSA investigate whether this is a broader safety defect affecting the Grand Highlander Hybrid MAX and whether the existing software repair is effective.
NHTSA complaint #11752231 — an unverified report by a vehicle owner.
After a complete stop at a stop sign there is hesitation/stalling when trying to accelerate. Sometimes the hesitation is several seconds and then the engine kicks in and lurches forward. Couple times this has been a safety issue as it happens when I’m trying to pull out on a busy road. The delay/hesitation has caused me to almost get hit a few times. There are no lights or warning messages when this happens. It happens a multiple times a week especially during hot weather when AC is on full (LO temp setting and maximum fan) and is usually during the first few minutes of operation usually at the same stop signs on my route to pickup my kids after the car has been sitting unused overnight. I also notice that the hybrid battery indicator is usually always at 3 bars. Dealership hasn’t been able to reproduce as it's a very specific scenario (not driving/in garage overnight and short drive). Instead they went and applied T-SB-0040-25 but this hesitation is still happening after the software update. This needs to be handled like a safety issue/recall worthy with a complete fix! Not just some drivability issue that only gets applied if we ask about specific T-SBs.
NHTSA complaint #11752130 — an unverified report by a vehicle owner.
I've had consistent issues with the vehicle accelerating and shifting. These include sluggish acceleration, loss of power and sputtering when we've come to a complete stop and starting to move again. We've almost been hit by other vehicles at least over 20 times because the vehicle has failed to accelerate when pulling into a roadway. The car hesitates during acceleration regardless of how much I push the gas. Once it starts to go, it feels as though the car can't shift from 1st to 2nd gear, The RPMs get extremely high while the car is going 25-40 mph and remain there for a few seconds up to ~20 seconds. I am fearful of getting t-boned when my car hesitates while turning at an intersection, going through an intersection or pulling out from a parking lot. I have been stuck in several intersections when traffic was coming toward me, but thankfully those cars had patience and avoided us. I've also found that this issue always happens when the hybrid battery shows that it only has a charge of 3 bars. It seems that the engine, transmission and hybrid battery don't know how to communicate when the battery charge gets that low. This has been happening since Dec 2023 when I bought the vehicle and the dealer has never been able to duplicate or find any error code, they are refusing to fix a known issue when many others are experiencing the same issue. There are Toyota Technical Service Bulletins (TSBs) out there regarding this problem but my dealer told me they won't do anything as it could label my vehicle a lemon. This is creating an unnecessary safety risk for me and my family.
NHTSA complaint #11750786 — an unverified report by a vehicle owner.
On occasion the car will not accelerate from a dead stop like it should. I think it’s turbo lag. There have been a few times I thought I was going be broadsided pulling out into traffic when normal acceleration would have been safe but with a dead pedal for a few seconds it was terrifying. I’ve brought this up to two different dealers and they say without being able to experience it there’s nothing they can do. Someone going to die because of this.
NHTSA complaint #11750898 — an unverified report by a vehicle owner.
After coming to a complete stop at a stop sign or stop light, then trying to go, the vehicle will stall. It will not go when given gas. The first time it happened, I was at a busy intersection with oncoming traffic coming towards me with the pedal to the floor, nothing would happen for 5-10 seconds. It was terrifying. Thank god the car coming towards us went around in time. It then happened again in my neighborhood a week later. Thankfully that time I wasn’t in traffic. I have noted that it seems to happen when very hot outside (Florida July summer) and air is on full blast. Also seems to be happening only during the first trip of the day, within the first 5-10 minutes of said trip. The dealership has not been able to recreate this to see for themselves. I think it would have to be with them overnight and they start it/drive it for the first time that day. It has now happened a total of 3 times since I’ve been driving it (2.5 months). I have 3 children and very worried I will get t-boned one day when it stalls next. I love my car so much so it’s heartbreaking that I have to drive it in fear. No lights/warnings/messages when this happens.
NHTSA complaint #11750573 — an unverified report by a vehicle owner.
Vehicle: 2024 Toyota Grand Highlander Hybrid Max The vehicle intermittently experiences a severe hesitation and shudder during acceleration from approximately 0-40 mph. The condition occurs only under specific circumstances: -The vehicle has been parked long enough for the engine, transmission, and related systems to cool to ambient air temperature. -The vehicle is started and driven shortly thereafter. -Engine oil and transmission temperatures are below approximately 160°F. -The air conditioning system is operating at maximum cooling with Eco Air Mode enabled. -The hybrid battery indicator displays approximately three bars of charge. When these precise conditions are present, the vehicle may hesitate, shudder, and fail to respond normally to accelerator pedal input during acceleration. Even with the accelerator pedal fully depressed, repeatedly, there is a noticeable delay in power delivery and vehicle acceleration. This creates a situation where the vehicle does not accelerate as expected when entering traffic or attempting to increase speed. The vehicle has previously received Toyota Technical Service Bulletin T-SB-0017-24; however, the condition continues to occur intermittently. No warning lights, diagnostic messages, or system faults are displayed when the event occurs. The condition typically occurs only once during the initial drive cycle after a cold start and has not been observed after the vehicle reaches normal operating temperature. The issue is most common in the warmer months and has never been encountered at freezing or below temperatures.
NHTSA complaint #11745922 — an unverified report by a vehicle owner.
A couple of days ago, I was driving when my Toyota Grand Highlander started displaying a series of alerts. These alerts included "Hybrid system malfunction" "All Wheel Drive malfunction," "Check engine. See dealer," and finally something akin to "Find a safe place to pull over and turn off vehicle." Until these alerts appeared, back-to-back-to-back, there were no indications that there was anything wrong with the car. We were fortunate enough to be both close to home and close to a dealership when this happened and were able to bring the car in right away. If we were in a high traffic situation, or, conversely, in a very rural area (specifically in winter, not an unlikely happening for us), having the car's drive system suddenly fail out of nowhere could have been very dangerous. As I said, we were able to get the car to the dealer soon after. The dealership informed us that the car has a coolant system perforation, more than likely from a rock penetrating the grill. The coolant than leaked, causing the hybrid system/other failures the car noted. I have since done some research on this issue and have found, to my dismay and disappointment, that this isn't an uncommon issue with the Grand Highlander and the Highlander. There are many instances of people on social media saying a similar issue happened with their cars - one other person's dealership quoted them the exact same amount of the repair that our dealership did. In fact, this is such a common issue that there is apparently already an established workaround: other owners have ordered aluminum mesh from third party vendors and have zip-tied it to their grills in order to keep the rocks out. This is an absurd thing to have to do. Consumers should not, in the year 2026, have to drive down the road with concern that a loose pebble will put their car out of commission. Cars should be able to withstand this very common occurrence without taking substantial damage. This seems like a design flaw.
NHTSA complaint #11745206 — an unverified report by a vehicle owner.
The electronic parking brake on my 2025 Toyota Grand Highlander intermittently fails to auto-release when shifting from Park to Reverse or Drive. Curiously, the system does respond to the gear shifter when returning to Park, as the brake will then engage or release as expected once cycled. This indicates a failure specifically in the transition out of the Park position. This intermittent delay or refusal to release prevents the vehicle from moving when expected, creating a potential safety hazard in traffic or during time-sensitive maneuvers. No dashboard warnings are present, and the issue occurs even when the driver's seat belt is buckled and the foot brake is fully depressed.
NHTSA complaint #11737288 — an unverified report by a vehicle owner.
The vehicle hesitates and does not accelerate immediately from a complete stop. This occurs more frequently when the car is on a slight incline. The delay in acceleration creates a safety concern, especially when attempting to merge into traffic or pull out onto a roadway. I have reported this issue to the dealership multiple times, but they have not taken action because they have been unable to reproduce the problem.
NHTSA complaint #11734376 — an unverified report by a vehicle owner.
I was driving toward the perimeter of my neighborhood, approaching an arterial cross street. When I braked the pedal went straight to the floor. The breaks didn’t work despite pumping them multiple times. I also heard the engine revving. To avoid the intersection and busy street I steered into a yard, hit a retaining wall and a tree, rolled and hit a metal city street sign. All airbags deployed. I was taken to the hospital by ambulance. The car was totaled and is on a temporary hold at a salvage yard.
NHTSA complaint #11727033 — an unverified report by a vehicle owner.