Lincoln Town CAR recalls

STEERING

Dorman Products, Inc. (Dorman) is recalling certain model Dorman Steering Shafts, part number 425-359, Solutions Steering Shafts, part number 7-0359, and OE Solutions Steering Shafts, part number 425-359, manufactured April 17, 2014, to September 28, 2015. These aftermarket replacement steering shafts are sold for use in 1995-2002 Ford Crown Victoria, Mercury Grand Marquis, and Lincoln Town Car vehicles. These steering shafts may separate during operation if the integral fastener is loose or missing and if the interfacing vehicle shaft is compressed in length.

Risk: If the shafts separate during vehicle operation, a loss of steering control would result, increasing the risk of a vehicle crash.

Remedy: Dorman will notify owners, and dealers will replace the steering shaft, free of charge. The recall began on October 28, 2015. Owners may contact Dorman customer service at 1-800-523-2492, option 5.

STEERING

Dorman Products, Inc. (Dorman) is recalling certain model Dorman Steering Shafts, part number 425-359, Solutions Steering Shafts, part number 7-0359, and OE Solutions Steering Shafts, part number 425-359, manufactured April 17, 2014, to September 28, 2015. These aftermarket replacement steering shafts are sold for use in 1995-2002 Ford Crown Victoria, Mercury Grand Marquis, and Lincoln Town Car vehicles. These steering shafts may separate during operation if the integral fastener is loose or missing and if the interfacing vehicle shaft is compressed in length.

Risk: If the shafts separate during vehicle operation, a loss of steering control would result, increasing the risk of a vehicle crash.

Remedy: Dorman will notify owners, and dealers will replace the steering shaft, free of charge. The recall began on October 28, 2015. Owners may contact Dorman customer service at 1-800-523-2492, option 5.

STEERING

Dorman Products, Inc. (Dorman) is recalling certain model Dorman Steering Shafts, part number 425-359, Solutions Steering Shafts, part number 7-0359, and OE Solutions Steering Shafts, part number 425-359, manufactured April 17, 2014, to September 28, 2015. These aftermarket replacement steering shafts are sold for use in 1995-2002 Ford Crown Victoria, Mercury Grand Marquis, and Lincoln Town Car vehicles. These steering shafts may separate during operation if the integral fastener is loose or missing and if the interfacing vehicle shaft is compressed in length.

Risk: If the shafts separate during vehicle operation, a loss of steering control would result, increasing the risk of a vehicle crash.

Remedy: Dorman will notify owners, and dealers will replace the steering shaft, free of charge. The recall began on October 28, 2015. Owners may contact Dorman customer service at 1-800-523-2492, option 5.

STEERING

Dorman Products, Inc. (Dorman) is recalling certain model Dorman Steering Shafts, part number 425-359, Solutions Steering Shafts, part number 7-0359, and OE Solutions Steering Shafts, part number 425-359, manufactured April 17, 2014, to September 28, 2015. These aftermarket replacement steering shafts are sold for use in 1995-2002 Ford Crown Victoria, Mercury Grand Marquis, and Lincoln Town Car vehicles. These steering shafts may separate during operation if the integral fastener is loose or missing and if the interfacing vehicle shaft is compressed in length.

Risk: If the shafts separate during vehicle operation, a loss of steering control would result, increasing the risk of a vehicle crash.

Remedy: Dorman will notify owners, and dealers will replace the steering shaft, free of charge. The recall began on October 28, 2015. Owners may contact Dorman customer service at 1-800-523-2492, option 5.

STEERING

Dorman Products, Inc. (Dorman) is recalling certain model Dorman Steering Shafts, part number 425-359, Solutions Steering Shafts, part number 7-0359, and OE Solutions Steering Shafts, part number 425-359, manufactured April 17, 2014, to September 28, 2015. These aftermarket replacement steering shafts are sold for use in 1995-2002 Ford Crown Victoria, Mercury Grand Marquis, and Lincoln Town Car vehicles. These steering shafts may separate during operation if the integral fastener is loose or missing and if the interfacing vehicle shaft is compressed in length.

Risk: If the shafts separate during vehicle operation, a loss of steering control would result, increasing the risk of a vehicle crash.

Remedy: Dorman will notify owners, and dealers will replace the steering shaft, free of charge. The recall began on October 28, 2015. Owners may contact Dorman customer service at 1-800-523-2492, option 5.

STEERING

Dorman Products, Inc. (Dorman) is recalling certain model Dorman Steering Shafts, part number 425-359, Solutions Steering Shafts, part number 7-0359, and OE Solutions Steering Shafts, part number 425-359, manufactured April 17, 2014, to September 28, 2015. These aftermarket replacement steering shafts are sold for use in 1995-2002 Ford Crown Victoria, Mercury Grand Marquis, and Lincoln Town Car vehicles. These steering shafts may separate during operation if the integral fastener is loose or missing and if the interfacing vehicle shaft is compressed in length.

Risk: If the shafts separate during vehicle operation, a loss of steering control would result, increasing the risk of a vehicle crash.

Remedy: Dorman will notify owners, and dealers will replace the steering shaft, free of charge. The recall began on October 28, 2015. Owners may contact Dorman customer service at 1-800-523-2492, option 5.

STEERING

Dorman Products, Inc. (Dorman) is recalling certain model Dorman Steering Shafts, part number 425-359, Solutions Steering Shafts, part number 7-0359, and OE Solutions Steering Shafts, part number 425-359, manufactured April 17, 2014, to September 28, 2015. These aftermarket replacement steering shafts are sold for use in 1995-2002 Ford Crown Victoria, Mercury Grand Marquis, and Lincoln Town Car vehicles. These steering shafts may separate during operation if the integral fastener is loose or missing and if the interfacing vehicle shaft is compressed in length.

Risk: If the shafts separate during vehicle operation, a loss of steering control would result, increasing the risk of a vehicle crash.

Remedy: Dorman will notify owners, and dealers will replace the steering shaft, free of charge. The recall began on October 28, 2015. Owners may contact Dorman customer service at 1-800-523-2492, option 5.

STEERING

Dorman Products, Inc. (Dorman) is recalling certain model Dorman Steering Shafts, part number 425-359, Solutions Steering Shafts, part number 7-0359, and OE Solutions Steering Shafts, part number 425-359, manufactured April 17, 2014, to September 28, 2015. These aftermarket replacement steering shafts are sold for use in 1995-2002 Ford Crown Victoria, Mercury Grand Marquis, and Lincoln Town Car vehicles. These steering shafts may separate during operation if the integral fastener is loose or missing and if the interfacing vehicle shaft is compressed in length.

Risk: If the shafts separate during vehicle operation, a loss of steering control would result, increasing the risk of a vehicle crash.

Remedy: Dorman will notify owners, and dealers will replace the steering shaft, free of charge. The recall began on October 28, 2015. Owners may contact Dorman customer service at 1-800-523-2492, option 5.

STEERING:RACK AND PINION:PINION SHAFT

Ford Motor Company (Ford) is recalling certain model year 2005-2011 Ford Crown Victoria, 2005-2011 Mercury Grand Marquis vehicles manufactured March 23, 2004, to August 30, 2011, and 2005-2011 Lincoln Town Car vehicles manufactured March 8, 2004, to August 30, 2011, and on which the upper intermediate shaft was serviced during the course of safety recall 13V-385. The prior repairs may not have been correctly performed.

Risk: Improper servicing of the upper intermediate shaft could cause the shaft to separate, which can then result in a loss of steering control, and increasing the risk of a crash.

Remedy: Ford will notify the owners of vehicles whose repair records reflect that the upper intermediate steering shaft was repaired during the course of the prior recall 13V-385. Dealers will inspect and replace the upper immediate shaft if necessary free of charge. The recall began November 17, 2014. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 14S25.

STEERING:RACK AND PINION:PINION SHAFT

Ford Motor Company (Ford) is recalling certain model year 2005-2011 Ford Crown Victoria, 2005-2011 Mercury Grand Marquis vehicles manufactured March 23, 2004, to August 30, 2011, and 2005-2011 Lincoln Town Car vehicles manufactured March 8, 2004, to August 30, 2011, and on which the upper intermediate shaft was serviced during the course of safety recall 13V-385. The prior repairs may not have been correctly performed.

Risk: Improper servicing of the upper intermediate shaft could cause the shaft to separate, which can then result in a loss of steering control, and increasing the risk of a crash.

Remedy: Ford will notify the owners of vehicles whose repair records reflect that the upper intermediate steering shaft was repaired during the course of the prior recall 13V-385. Dealers will inspect and replace the upper immediate shaft if necessary free of charge. The recall began November 17, 2014. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 14S25.

STEERING:RACK AND PINION:PINION SHAFT

Ford Motor Company (Ford) is recalling certain model year 2005-2011 Ford Crown Victoria, 2005-2011 Mercury Grand Marquis vehicles manufactured March 23, 2004, to August 30, 2011, and 2005-2011 Lincoln Town Car vehicles manufactured March 8, 2004, to August 30, 2011, and on which the upper intermediate shaft was serviced during the course of safety recall 13V-385. The prior repairs may not have been correctly performed.

Risk: Improper servicing of the upper intermediate shaft could cause the shaft to separate, which can then result in a loss of steering control, and increasing the risk of a crash.

Remedy: Ford will notify the owners of vehicles whose repair records reflect that the upper intermediate steering shaft was repaired during the course of the prior recall 13V-385. Dealers will inspect and replace the upper immediate shaft if necessary free of charge. The recall began November 17, 2014. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 14S25.

STEERING:RACK AND PINION:PINION SHAFT

Ford Motor Company (Ford) is recalling certain model year 2005-2011 Ford Crown Victoria, 2005-2011 Mercury Grand Marquis vehicles manufactured March 23, 2004, to August 30, 2011, and 2005-2011 Lincoln Town Car vehicles manufactured March 8, 2004, to August 30, 2011, and on which the upper intermediate shaft was serviced during the course of safety recall 13V-385. The prior repairs may not have been correctly performed.

Risk: Improper servicing of the upper intermediate shaft could cause the shaft to separate, which can then result in a loss of steering control, and increasing the risk of a crash.

Remedy: Ford will notify the owners of vehicles whose repair records reflect that the upper intermediate steering shaft was repaired during the course of the prior recall 13V-385. Dealers will inspect and replace the upper immediate shaft if necessary free of charge. The recall began November 17, 2014. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 14S25.

STEERING

Ford is recalling certain model year 2005-2011 Ford Crown Victoria (including Crown Victoria Police Interceptors), Mercury Grand Marquis, and Lincoln Town Car vehicles. The affected vehicles are currently registered or were originally sold in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. Severe corrosion can seize the lower intermediate shaft which may cause the upper intermediate shaft to collapse and the steering column lower bearing to separate.

Risk: If the lower bearing separates, the vehicle may experience a loss of steering, increasing the risk of a crash.

Remedy: Ford will notify owners and dealers will replace the lower intermediate shaft, free of charge. The upper intermediate shaft and steering column lower bearing will be inspected to identify any damage that may have occurred as a result of lower intermediate shaft corrosion, and repaired or replaced as necessary. If the steering column lower bearing has separated, a retainer clip will be installed. The recall began on October 23, 2013. Owners may contact Ford at 1-866-436-7332. Ford's recall number is 13S08.

STEERING

Ford is recalling certain model year 2005-2011 Ford Crown Victoria (including Crown Victoria Police Interceptors), Mercury Grand Marquis, and Lincoln Town Car vehicles. The affected vehicles are currently registered or were originally sold in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. Severe corrosion can seize the lower intermediate shaft which may cause the upper intermediate shaft to collapse and the steering column lower bearing to separate.

Risk: If the lower bearing separates, the vehicle may experience a loss of steering, increasing the risk of a crash.

Remedy: Ford will notify owners and dealers will replace the lower intermediate shaft, free of charge. The upper intermediate shaft and steering column lower bearing will be inspected to identify any damage that may have occurred as a result of lower intermediate shaft corrosion, and repaired or replaced as necessary. If the steering column lower bearing has separated, a retainer clip will be installed. The recall began on October 23, 2013. Owners may contact Ford at 1-866-436-7332. Ford's recall number is 13S08.

STEERING

Ford is recalling certain model year 2005-2011 Ford Crown Victoria (including Crown Victoria Police Interceptors), Mercury Grand Marquis, and Lincoln Town Car vehicles. The affected vehicles are currently registered or were originally sold in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. Severe corrosion can seize the lower intermediate shaft which may cause the upper intermediate shaft to collapse and the steering column lower bearing to separate.

Risk: If the lower bearing separates, the vehicle may experience a loss of steering, increasing the risk of a crash.

Remedy: Ford will notify owners and dealers will replace the lower intermediate shaft, free of charge. The upper intermediate shaft and steering column lower bearing will be inspected to identify any damage that may have occurred as a result of lower intermediate shaft corrosion, and repaired or replaced as necessary. If the steering column lower bearing has separated, a retainer clip will be installed. The recall began on October 23, 2013. Owners may contact Ford at 1-866-436-7332. Ford's recall number is 13S08.

STEERING

Ford is recalling certain model year 2005-2011 Ford Crown Victoria (including Crown Victoria Police Interceptors), Mercury Grand Marquis, and Lincoln Town Car vehicles. The affected vehicles are currently registered or were originally sold in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. Severe corrosion can seize the lower intermediate shaft which may cause the upper intermediate shaft to collapse and the steering column lower bearing to separate.

Risk: If the lower bearing separates, the vehicle may experience a loss of steering, increasing the risk of a crash.

Remedy: Ford will notify owners and dealers will replace the lower intermediate shaft, free of charge. The upper intermediate shaft and steering column lower bearing will be inspected to identify any damage that may have occurred as a result of lower intermediate shaft corrosion, and repaired or replaced as necessary. If the steering column lower bearing has separated, a retainer clip will be installed. The recall began on October 23, 2013. Owners may contact Ford at 1-866-436-7332. Ford's recall number is 13S08.

ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE

EXECUTIVE COACH IS RECALLING CERTAIN MODEL YEAR 2008-2011 LINCOLN TOWN CAR LIMOUSINES. THE FUEL RAIL SHIELD WAS LEFT OFF DURING MANUFACTURING. IN A FRONTAL IMPACT THE ENGINE COULD POTENTIALLY BEND OR RUPTURE FUEL LINES IF THE REPLACEMENT SHIELD IS NOT IN PLACE, CAUSING THOSE LINES TO LEAK FUEL.

Risk: FUEL LEAKAGE, IN THE PRESENCE OF AN IGNITION SOURCE, COULD RESULT IN A FIRE.

Remedy: EXECUTIVE COACH WILL SUPPLY KITS AND INSTALLATION INSTRUCTIONS TO HAVE VEHICLES REPAIRED AT A FACILITY OF THE OWNER'S CHOICE. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON DECEMBER 1, 2010. OWNERS MAY CONTACT EXECUTIVE COACH AT 888-322-9272.

VEHICLE SPEED CONTROL

ON CERTAIN PICKUP TRUCKS, PASSENGER VEHICLES, SPORT UTILITY VEHICLES, AND MOTOR HOMES CHASSIS, THE SPEED CONTROL DEACTIVATION SWITCH MAY, UNDER CERTAIN CONDITIONS, LEAK INTERNALLY AND THEN OVERHEAT, SMOKE, OR BURN.

Risk: THIS COULD RESULT IN AN UNDERHOOD FIRE.

Remedy: DEALERS WILL INSTALL A FUSED WIRING HARNESS. OWNERS OF THE PASSENGER CARS INCLUDED IN THIS CAMPAIGN WILL BE INSTRUCTED TO RETURN THEIR VEHICLES TO THEIR DEALERS TO HAVE THE SPEED CONTROL DEACTIVATION SWITCH DISCONNECTED AS AN INTERIM REPAIR. AS SOON AS REPAIR PARTS ARE AVAILABLE (EXPECTED OCTOBER 2007), OWNERS WILL BE INSTRUCTED TO RETURN TO THE DEALERS FOR INSTALLATION OF A FUSED WIRING HARNESS. THE RECALL BEGAN ON AUGUST 13, 2007, AND MAILING COMPLETED BY SEPTEMBER 19, 2007. OWNERS MAY CONTACT FORD AT 1-888-222-2751.

VEHICLE SPEED CONTROL

ON CERTAIN PICKUP TRUCKS, PASSENGER VEHICLES, SPORT UTILITY VEHICLES, AND MOTOR HOMES CHASSIS, THE SPEED CONTROL DEACTIVATION SWITCH MAY, UNDER CERTAIN CONDITIONS, LEAK INTERNALLY AND THEN OVERHEAT, SMOKE, OR BURN.

Risk: THIS COULD RESULT IN AN UNDERHOOD FIRE.

Remedy: DEALERS WILL INSTALL A FUSED WIRING HARNESS. OWNERS OF THE PASSENGER CARS INCLUDED IN THIS CAMPAIGN WILL BE INSTRUCTED TO RETURN THEIR VEHICLES TO THEIR DEALERS TO HAVE THE SPEED CONTROL DEACTIVATION SWITCH DISCONNECTED AS AN INTERIM REPAIR. AS SOON AS REPAIR PARTS ARE AVAILABLE (EXPECTED OCTOBER 2007), OWNERS WILL BE INSTRUCTED TO RETURN TO THE DEALERS FOR INSTALLATION OF A FUSED WIRING HARNESS. THE RECALL BEGAN ON AUGUST 13, 2007, AND MAILING COMPLETED BY SEPTEMBER 19, 2007. OWNERS MAY CONTACT FORD AT 1-888-222-2751.

VEHICLE SPEED CONTROL

ON CERTAIN PICKUP TRUCKS, PASSENGER VEHICLES, SPORT UTILITY VEHICLES, AND MOTOR HOMES CHASSIS, THE SPEED CONTROL DEACTIVATION SWITCH MAY, UNDER CERTAIN CONDITIONS, LEAK INTERNALLY AND THEN OVERHEAT, SMOKE, OR BURN.

Risk: THIS COULD RESULT IN AN UNDERHOOD FIRE.

Remedy: DEALERS WILL INSTALL A FUSED WIRING HARNESS. OWNERS OF THE PASSENGER CARS INCLUDED IN THIS CAMPAIGN WILL BE INSTRUCTED TO RETURN THEIR VEHICLES TO THEIR DEALERS TO HAVE THE SPEED CONTROL DEACTIVATION SWITCH DISCONNECTED AS AN INTERIM REPAIR. AS SOON AS REPAIR PARTS ARE AVAILABLE (EXPECTED OCTOBER 2007), OWNERS WILL BE INSTRUCTED TO RETURN TO THE DEALERS FOR INSTALLATION OF A FUSED WIRING HARNESS. THE RECALL BEGAN ON AUGUST 13, 2007, AND MAILING COMPLETED BY SEPTEMBER 19, 2007. OWNERS MAY CONTACT FORD AT 1-888-222-2751.

VEHICLE SPEED CONTROL

ON CERTAIN PICKUP TRUCKS, PASSENGER VEHICLES, SPORT UTILITY VEHICLES, AND MOTOR HOMES CHASSIS, THE SPEED CONTROL DEACTIVATION SWITCH MAY, UNDER CERTAIN CONDITIONS, LEAK INTERNALLY AND THEN OVERHEAT, SMOKE, OR BURN.

Risk: THIS COULD RESULT IN AN UNDERHOOD FIRE.

Remedy: DEALERS WILL INSTALL A FUSED WIRING HARNESS. OWNERS OF THE PASSENGER CARS INCLUDED IN THIS CAMPAIGN WILL BE INSTRUCTED TO RETURN THEIR VEHICLES TO THEIR DEALERS TO HAVE THE SPEED CONTROL DEACTIVATION SWITCH DISCONNECTED AS AN INTERIM REPAIR. AS SOON AS REPAIR PARTS ARE AVAILABLE (EXPECTED OCTOBER 2007), OWNERS WILL BE INSTRUCTED TO RETURN TO THE DEALERS FOR INSTALLATION OF A FUSED WIRING HARNESS. THE RECALL BEGAN ON AUGUST 13, 2007, AND MAILING COMPLETED BY SEPTEMBER 19, 2007. OWNERS MAY CONTACT FORD AT 1-888-222-2751.

VEHICLE SPEED CONTROL

ON CERTAIN PICKUP TRUCKS, PASSENGER VEHICLES, SPORT UTILITY VEHICLES, AND MOTOR HOMES CHASSIS, THE SPEED CONTROL DEACTIVATION SWITCH MAY, UNDER CERTAIN CONDITIONS, LEAK INTERNALLY AND THEN OVERHEAT, SMOKE, OR BURN.

Risk: THIS COULD RESULT IN AN UNDERHOOD FIRE.

Remedy: DEALERS WILL INSTALL A FUSED WIRING HARNESS. OWNERS OF THE PASSENGER CARS INCLUDED IN THIS CAMPAIGN WILL BE INSTRUCTED TO RETURN THEIR VEHICLES TO THEIR DEALERS TO HAVE THE SPEED CONTROL DEACTIVATION SWITCH DISCONNECTED AS AN INTERIM REPAIR. AS SOON AS REPAIR PARTS ARE AVAILABLE (EXPECTED OCTOBER 2007), OWNERS WILL BE INSTRUCTED TO RETURN TO THE DEALERS FOR INSTALLATION OF A FUSED WIRING HARNESS. THE RECALL BEGAN ON AUGUST 13, 2007, AND MAILING COMPLETED BY SEPTEMBER 19, 2007. OWNERS MAY CONTACT FORD AT 1-888-222-2751.

VEHICLE SPEED CONTROL

ON CERTAIN PICKUP TRUCKS, PASSENGER VEHICLES, SPORT UTILITY VEHICLES, AND MOTOR HOMES CHASSIS, THE SPEED CONTROL DEACTIVATION SWITCH MAY, UNDER CERTAIN CONDITIONS, LEAK INTERNALLY AND THEN OVERHEAT, SMOKE, OR BURN.

Risk: THIS COULD RESULT IN AN UNDERHOOD FIRE.

Remedy: DEALERS WILL INSTALL A FUSED WIRING HARNESS. OWNERS OF THE PASSENGER CARS INCLUDED IN THIS CAMPAIGN WILL BE INSTRUCTED TO RETURN THEIR VEHICLES TO THEIR DEALERS TO HAVE THE SPEED CONTROL DEACTIVATION SWITCH DISCONNECTED AS AN INTERIM REPAIR. AS SOON AS REPAIR PARTS ARE AVAILABLE (EXPECTED OCTOBER 2007), OWNERS WILL BE INSTRUCTED TO RETURN TO THE DEALERS FOR INSTALLATION OF A FUSED WIRING HARNESS. THE RECALL BEGAN ON AUGUST 13, 2007, AND MAILING COMPLETED BY SEPTEMBER 19, 2007. OWNERS MAY CONTACT FORD AT 1-888-222-2751.

VEHICLE SPEED CONTROL

ON CERTAIN PICKUP TRUCKS, PASSENGER VEHICLES, SPORT UTILITY VEHICLES, AND MOTOR HOMES CHASSIS, THE SPEED CONTROL DEACTIVATION SWITCH MAY, UNDER CERTAIN CONDITIONS, LEAK INTERNALLY AND THEN OVERHEAT, SMOKE, OR BURN.

Risk: THIS COULD RESULT IN AN UNDERHOOD FIRE.

Remedy: DEALERS WILL INSTALL A FUSED WIRING HARNESS. OWNERS OF THE PASSENGER CARS INCLUDED IN THIS CAMPAIGN WILL BE INSTRUCTED TO RETURN THEIR VEHICLES TO THEIR DEALERS TO HAVE THE SPEED CONTROL DEACTIVATION SWITCH DISCONNECTED AS AN INTERIM REPAIR. AS SOON AS REPAIR PARTS ARE AVAILABLE (EXPECTED OCTOBER 2007), OWNERS WILL BE INSTRUCTED TO RETURN TO THE DEALERS FOR INSTALLATION OF A FUSED WIRING HARNESS. THE RECALL BEGAN ON AUGUST 13, 2007, AND MAILING COMPLETED BY SEPTEMBER 19, 2007. OWNERS MAY CONTACT FORD AT 1-888-222-2751.

SUSPENSION:FRONT:HUB

ON CERTAIN PASSENGER VEHICLES, A FRONT WHEEL BEARING AND HUB ASSEMBLY MAY FRACTURE DUE TO IMPROPER HEAT TREATMENT.

Risk: IF A HUB FRACTURES, IT MAY POTENTIALLY DETACH FROM THE WHEEL KNUCKLE, RESULTING IN THE WHEEL BEING RETAINED ONLY BY THE BRAKE CALIPER ASSEMBLY. AS A RESULT, THE WHEEL MAY SEPARATE FROM THE VEHICLE POTENTIALLY RESULTING IN A CRASH.

Remedy: DEALERS WILL INSPECT BOTH FRONT WHEEL BEARING AND HUB ASSEMBLIES AND REPLACE THEM FREE OF CHARGE. THE RECALL BEGAN ON JUNE 22, 2007. OWNERS MAY CONTACT FORD AT 1-800-392-3673.

ELECTRICAL SYSTEM:12V/24V/48V BATTERY:CABLES

ON CERTAIN PASSENGER VEHICLES, THE BATTERY CABLE INCLUDES A FUSIBLE LINK THAT MAY CONTACT AND SUBSEQUENTLY CHAFE ON A #2 CROSS MEMBER ATTACHING BOLT.

Risk: THIS CONDITION MAY RESULT IN HEAT DAMAGE AND COULD LEAD TO A FIRE.

Remedy: DEALERS WILL INSPECT THE FUSIBLE LINK AND POSITION IT AWAY FROM THE CROSS MEMBER BOLT. IF THE FUSIBLE LINK HAS ALREADY CHAFED AND COPPER WIRES HAVE BEEN EXPOSED, THE FUSIBLE LINK WILL BE REPLACED. THE RECALL BEGAN ON NOVEMBER 18, 2005. OWNERS MAY CONTACT FORD AT 1-800-392-3673, OR LINCOLN/MERCURY AT 1-800-521-4140.

SUSPENSION:REAR

CERTAIN POLICE, COMMERCIAL, AND PASSENGER VEHICLES SOLD TO FLEETS TYPICALLY INPUT HIGHER LOADS INTO THE VEHICLE CHASSIS OVERLOADING THE WHEEL BEARINGS AND AXLES.

Risk: THIS COULD LEAD TO EARLY BEARING FAILURE AND ULTIMATELY TO AXLE SHAFT FRACTURE. IN THE EVENT OF AXLE SHAFT FRACTURE, THE VEHICLE WOULD LOSE DRIVE FUNCTION AND WOULD COAST TO A STOP. LOSS OF DRIVE FUNCTION COULD LEAD TO A CRASH.

Remedy: DEALERS WILL REPLACE THE REAR WHEEL BEARINGS, SEALS,AND AXLE SHAFTS. THE RECALL BEGAN ON JULY 15, 2004. OWNERS SHOULD CONTACT FORD AT 1-800-392-3673.

AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE

EQUIPMENT DESCRIPTION: PASSENGER VEHICLES THAT HAVE HAD THE DRIVER'S AIR BAG MODULE REPLACED AFTER APRIL 5, 2000. THE REPLACEMENT DRIVER'S AIR BAG MODULE INFLATOR MAY HAVE INSUFFICIENT WELDS THAT COULD PREVENT PROPER INFLATION OF THE AIR BAG.

Risk: IN THE EVENT OF A CRASH, THE DRIVER'S AIR BAG MAY NOT PROPERLY DEPLOY WHICH COULD POTENTIALLY RESULT IN LESS THAN THE INTENDED LEVEL OF OCCUPANT PROTECTION.

Remedy: DEALERS WILL INSPECT AND, IF NECESSARY, REPLACE THE DRIVER'S AIR BAG MODULE. OWNER NOTIFICATION BEGAN OCTOBER 5, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-866-436-7332.

AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE

EQUIPMENT DESCRIPTION: PASSENGER VEHICLES THAT HAVE HAD THE DRIVER'S AIR BAG MODULE REPLACED AFTER APRIL 5, 2000. THE REPLACEMENT DRIVER'S AIR BAG MODULE INFLATOR MAY HAVE INSUFFICIENT WELDS THAT COULD PREVENT PROPER INFLATION OF THE AIR BAG.

Risk: IN THE EVENT OF A CRASH, THE DRIVER'S AIR BAG MAY NOT PROPERLY DEPLOY WHICH COULD POTENTIALLY RESULT IN LESS THAN THE INTENDED LEVEL OF OCCUPANT PROTECTION.

Remedy: DEALERS WILL INSPECT AND, IF NECESSARY, REPLACE THE DRIVER'S AIR BAG MODULE. OWNER NOTIFICATION BEGAN OCTOBER 5, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-866-436-7332.

AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE

EQUIPMENT DESCRIPTION: PASSENGER VEHICLES THAT HAVE HAD THE DRIVER'S AIR BAG MODULE REPLACED AFTER APRIL 5, 2000. THE REPLACEMENT DRIVER'S AIR BAG MODULE INFLATOR MAY HAVE INSUFFICIENT WELDS THAT COULD PREVENT PROPER INFLATION OF THE AIR BAG.

Risk: IN THE EVENT OF A CRASH, THE DRIVER'S AIR BAG MAY NOT PROPERLY DEPLOY WHICH COULD POTENTIALLY RESULT IN LESS THAN THE INTENDED LEVEL OF OCCUPANT PROTECTION.

Remedy: DEALERS WILL INSPECT AND, IF NECESSARY, REPLACE THE DRIVER'S AIR BAG MODULE. OWNER NOTIFICATION BEGAN OCTOBER 5, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-866-436-7332.

VISIBILITY:WINDSHIELD WIPER/WASHER:MOTOR

VEHICLE DESCRIPTION: PASSENGER CARS, SPORT UTILITY VEHICLES, AND LIGHT AND MEDIUM DUTY PICKUP TRUCKS. A SWITCH LOCATED IN THE PLASTIC COVER OF THE WIPER MOTOR GEAR CASE COULD MALFUNCTION AND OVERHEAT, POTENTIALLY RESULTING IN LOSS OF INTERMITTENT WIPER FUNCTION, LOSS OF WIPER PARK FUNCTION, COMPLETE LOSS OF WIPER FUNCTION, OR IGNITION OF THE PLASTIC COVER MATERIAL. SWITCH MALFUNCTION IS MOST LIKELY TO OCCUR WHEN THE INTERMITTENT SETTING OF THE WIPERS IS BEING USED, OR WHEN SNOW OR ICE OBSTRUCTS THE BLADES FROM RETURNING TO THE "PARKED" POSITION AT THE BOTTOM OF THE WINDSHIELD. THESE VEHICLES WERE BUILT AT THE FOLLOWING ASSEMBLY PLANTS: ATLANTA PLANT FROM 2/11/00 THROUGH 7/31/00; CHICAGO PLANT FROM 2/14/00 THROUGH 8/4/00; KANSAS CITY PLANT FROM 2/26/00 TO 9/4/00; KENTUCKY TRUCK PLANT FROM 2/18/00 TO 8/31/00; MICHIGAN TRUCK PLANT FROM 2/23/00 THROUGH 8/3/00; NORFOLK PLANT FROM 2/21/00 THROUGH 7/27/00; WAYNE STAMPING AND ASSEMBLY PLANT FROM 2/25/00 THROUGH 8/15/00; AND WIXOM PLANT FROM 2/15/00 THROUGH 8/8/00.

Risk: LOSS OF VISIBILITY WHILE DRIVING INCREASES THE RISK OF A CRASH.

Remedy: DEALERS WILL INSPECT THE DATE CODE ON THE WIPER MOTOR. MOTORS BUILT WITH THE SUSPECT TIME FRAME WILL HAVE THE WIPER MOTOR GEAR CASE COVER REPLACED. OWNER NOTIFICATION BEGAN AUGUST 20, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-866-436-7332.

VISIBILITY:WINDSHIELD WIPER/WASHER:MOTOR

VEHICLE DESCRIPTION: PASSENGER CARS, SPORT UTILITY VEHICLES, AND LIGHT AND MEDIUM DUTY PICKUP TRUCKS. A SWITCH LOCATED IN THE PLASTIC COVER OF THE WIPER MOTOR GEAR CASE COULD MALFUNCTION AND OVERHEAT, POTENTIALLY RESULTING IN LOSS OF INTERMITTENT WIPER FUNCTION, LOSS OF WIPER PARK FUNCTION, COMPLETE LOSS OF WIPER FUNCTION, OR IGNITION OF THE PLASTIC COVER MATERIAL. SWITCH MALFUNCTION IS MOST LIKELY TO OCCUR WHEN THE INTERMITTENT SETTING OF THE WIPERS IS BEING USED, OR WHEN SNOW OR ICE OBSTRUCTS THE BLADES FROM RETURNING TO THE "PARKED" POSITION AT THE BOTTOM OF THE WINDSHIELD. THESE VEHICLES WERE BUILT AT THE FOLLOWING ASSEMBLY PLANTS: ATLANTA PLANT FROM 2/11/00 THROUGH 7/31/00; CHICAGO PLANT FROM 2/14/00 THROUGH 8/4/00; KANSAS CITY PLANT FROM 2/26/00 TO 9/4/00; KENTUCKY TRUCK PLANT FROM 2/18/00 TO 8/31/00; MICHIGAN TRUCK PLANT FROM 2/23/00 THROUGH 8/3/00; NORFOLK PLANT FROM 2/21/00 THROUGH 7/27/00; WAYNE STAMPING AND ASSEMBLY PLANT FROM 2/25/00 THROUGH 8/15/00; AND WIXOM PLANT FROM 2/15/00 THROUGH 8/8/00.

Risk: LOSS OF VISIBILITY WHILE DRIVING INCREASES THE RISK OF A CRASH.

Remedy: DEALERS WILL INSPECT THE DATE CODE ON THE WIPER MOTOR. MOTORS BUILT WITH THE SUSPECT TIME FRAME WILL HAVE THE WIPER MOTOR GEAR CASE COVER REPLACED. OWNER NOTIFICATION BEGAN AUGUST 20, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-866-436-7332.

SEAT BELTS:FRONT:BUCKLE ASSEMBLY

VEHICLE DESCRIPTION: PASSENGER AND SPORT UTILITY VEHICLES, PICKUP TRUCKS, AND MINIVANS. EQUIPPED WITH SEAT BELTS SUPPLIED BY TRW. IT IS POSSIBLE THAT THE DRIVER'S AND/OR FRONT PASSENGER'S OUTBOARD SEAT BELT BUCKLE MAY NOT FULLY LATCH. FORD CROWN VICTORIA BUILT AT ST. THOMAS ASSEMBLY PLANT FROM 4/17/00 - 5/29/01 MERCURY GRAND MARQUIS BUILT AT ST. THOMAS ASSEMBLY PLANT FROM 4/17/00 - 5/29/01. LINCOLN TOWN CARS BUILT AT WIXOM ASSEMBLY PLANT FROM 3/27/00 - 5/30/01. LINCOLN NAVIGATORS BUILT AT MICHIGAN TRUCK PLANT FROM 4/11/00 - 5/31/01. FORD WINDSTARS BUILT AT OAKVILLE ASSEMBLY PLANT FROM 3/23/00 - 5/30/01. FORD RANGERS BUILT AT TWIN CITIES PLANT FROM 3/28/00 - 5/30/01, AND ALSO AT THE EDISON PLANT FROM 3/13/00 - 5/25/01. FORD F-150 TRUCK BUILT AT NORFOLK PLANT FROM 4/18/00 - 5/25/00; AT ONTARIO PLANT FROM 5/10/00 - 5/28/01; AT KANSAS CITY PLANT FROM 9/11/99 - 5/25/01; AND AT CUAUTITLAN PLANT FROM 5/16/00 - 6/9/01. FORD SUPER DUTY F-250, F-350, F-450, AND F-550 TRUCKS BUILT AT KENTUCKY PLANT FROM 4/17/00 - 5/27/01; AND AT CUAUTITLAN PLANT FROM 5/16/00 - 6/19/01. FORD EXCURSIONS BUILT AT KENTUCKY PLANT FROM 4/17/00 - 10/2/00. FORD EXPEDITIONS BUILT AT MICHIGAN TRUCK PLANT FROM 4/11/00 -

Risk: IN THE EVENT OF A CRASH, THE RESTRAINT SYSTEM MAY NOT PROVIDE ADEQUATE OCCUPANT PROTECTION, INCREASING THE RISK OF PERSONAL INJURY TO THE SEAT OCCUPANT.

Remedy: DEALERS WILL INSPECT THE FRONT OUTBOARD SEAT BELT BUCKLES AND IF THE BUCKLE FAILS THE INSPECTION PROCESS, IT WILL BE REPLACED. OWNER NOTIFICATION BEGAN JULY 25, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-866-436-7332.

TIRES

VEHICLE DESCRIPTION: CERTAIN LIMOUSINES STRETCHED OVER 60 INCHES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 109, "NEW PNEUMATIC TIRES," AND NO. 110, "TIRE SELECTION AND RIMS."

Risk: THE VEHICLE WEIGHT COULD EXCEED THE MAXIMUM LOAD RATING FOR THE TIRE, INCREASING THE RISK OF PREMATURE TIRE WEAR OR BLOWOUT.

Remedy: DEALERS WILL REPLACE ALL 5 TIRES (INCLUDING THE SPARE TIRE) WITH MICHELIN TIRES (225/70R16 107T REINFORCED WHITE SIDEWALL) WITH A SUFFICIENTLY HIGHER LOAD RATING. OWNER NOTIFICATION BEGAN JANUARY 10, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-800-248-0186.

TIRES

VEHICLE DESCRIPTION: CERTAIN LIMOUSINES STRETCHED OVER 60 INCHES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 109, "NEW PNEUMATIC TIRES," AND NO. 110, "TIRE SELECTION AND RIMS."

Risk: THE VEHICLE WEIGHT COULD EXCEED THE MAXIMUM LOAD RATING FOR THE TIRE, INCREASING THE RISK OF PREMATURE TIRE WEAR OR BLOWOUT.

Remedy: DEALERS WILL REPLACE ALL 5 TIRES (INCLUDING THE SPARE TIRE) WITH MICHELIN TIRES (225/70R16 107T REINFORCED WHITE SIDEWALL) WITH A SUFFICIENTLY HIGHER LOAD RATING. OWNER NOTIFICATION BEGAN JANUARY 10, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-800-248-0186.

TIRES

VEHICLE DESCRIPTION: CERTAIN LIMOUSINES STRETCHED OVER 60 INCHES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 109, "NEW PNEUMATIC TIRES," AND NO. 110, "TIRE SELECTION AND RIMS."

Risk: THE VEHICLE WEIGHT COULD EXCEED THE MAXIMUM LOAD RATING FOR THE TIRE, INCREASING THE RISK OF PREMATURE TIRE WEAR OR BLOWOUT.

Remedy: DEALERS WILL REPLACE ALL 5 TIRES (INCLUDING THE SPARE TIRE) WITH MICHELIN TIRES (225/70R16 107T REINFORCED WHITE SIDEWALL) WITH A SUFFICIENTLY HIGHER LOAD RATING. OWNER NOTIFICATION BEGAN JANUARY 10, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-800-248-0186.

TIRES

VEHICLE DESCRIPTION: CERTAIN LIMOUSINES STRETCHED OVER 60 INCHES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 109, "NEW PNEUMATIC TIRES," AND NO. 110, "TIRE SELECTION AND RIMS."

Risk: THE VEHICLE WEIGHT COULD EXCEED THE MAXIMUM LOAD RATING FOR THE TIRE, INCREASING THE RISK OF PREMATURE TIRE WEAR OR BLOWOUT.

Remedy: DEALERS WILL REPLACE ALL 5 TIRES (INCLUDING THE SPARE TIRE) WITH MICHELIN TIRES (225/70R16 107T REINFORCED WHITE SIDEWALL) WITH A SUFFICIENTLY HIGHER LOAD RATING. OWNER NOTIFICATION BEGAN JANUARY 10, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-800-248-0186.

AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE-INACTIVE

VEHICLE DESCRIPTION: MINIVANS AND PASSENGER VEHICLES. A RESTRAINT CONTROL MODULE (RCM) OR A SIDE OR FRONT CRASH SENSOR MAY HAVE BEEN ASSEMBLED WITH ONE OR MORE OF THE SCREWS THAT MOUNT THE CIRCUIT BOARD IN THE HOUSING MISSING. IF SOME OR ALL OF THE SCREWS ARE MISSING, THE PERFORMANCE OF THE OCCUPANT RESTRAINS COULD BE AFFECTED.

Risk: IN SOME CASES, LESS THAN THE INTENDED LEVEL OF PROTECTION IN THE EVENT OF A CRASH.

Remedy: DEALERS WILL INSPECT THE RCM AND CRASH SENSORS AND, IF NECESSARY, REPLACE THEM.

SEAT BELTS:FRONT

VEHICLE DESCRIPTION: CERTAIN PASSENGER VEHICLES WITH MEDIUM GRAPHITE SEAT BELTS FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." AN INCORRECT FRONT CENTER SEAT BELT AND RETRACTOR ASSEMBLY MAY HAVE BEEN INSTALLED.

Risk: IN THE EVENT OF A VEHICLE CRASH, THE OCCUPANT MAY NOT BE PROPERLY RESTRAINED.

Remedy: ALL SUSPECT VEHICLES HAVE HAD THE SEAT BELTS INSPECTED OR REPLACED BY FORD.

SEAT BELTS:REAR/OTHER

VEHICLE DESCRIPTION: PASSENGER VEHICLES WITH MIDNIGHT BLACK OR MEDIUM PARCHMENT SEAT BELTS MANUFACTURED ON JULY 31, 2000, FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." AN INCORRECT DRIVER'S SIDE REAR SEAT BELT AND RETRACTOR ASSEMBLY MAY HAVE BEEN INSTALLED.

Risk: IN THE EVENT OF A VEHICLE CRASH, THE OCCUPANT MAY NOT BE PROPERLY RESTRAINED.

Remedy: DEALERS WILL INSPECT THE SEAT BELTS AND REPLACE THE AFFECTED SEAT BELT AND RETRACTOR ASSEMBLIES.

AIR BAGS

CERTAIN PASSENGER VEHICLES, LIMOUSINES, AND MINI VANS WERE BUILT WITH A NEWLY DESIGNED RESTRAINT CONTROL MODULE (RCM). IN SOME CASES, THE RCM DOES NOT RECOGNIZE CERTAIN SYSTEM FAULTS THAT COULD RESULT IN AN AIR BAG OR SEAT BELT PRE-TENSIONER UNEXPECTEDLY ACTIVATING DURING THE SELF-TEST SEQUENCE AT VEHICLE START-UP.

Risk: THIS CONDITION COULD RESULT IN PERSONAL INJURY.

Remedy: DEALERS WILL REPLACE THE RCM IN THESE VEHICLES. OWNER NOTIFICATION BEGAN SEPTEMBER 14, 2000. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-800-392-3673.

SEAT BELTS

VEHICLE DESCRIPTION: PASSENGER VEHICLES, LIGHT DUTY TRUCKS, SPORT UTILITY VEHICLES, AND MINI VANS EQUIPPED WITH TRW SEAT BELT BUCKLE ASSEMBLIES. THE BUCKLE BASE OF THESE SEAT BELT ASSEMBLIES WERE NOT PROPERLY HEAT TREATED AND THEREFORE DO NOT PASS THE LOAD BEARING REQUIREMENT OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, "SEAT BELT ASSEMBLIES."

Risk: IN THE EVENT OF A VEHICLE CRASH, THE OCCUPANT MAY NOT BE PROPERLY RESTRAINED.

Remedy: DEALERS WILL INSPECT THE DATE CODE ON CERTAIN SEAT BELT BUCKLES OF YOUR VEHICLE AND REPLACE ALL SEAT BELT BUCKLES THAT FALL WITHIN THE SUSPECT DATE CODE RANGE. OWNER NOTIFICATION BEGAN OCTOBER 26, 2000. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-800-392-3673.

EQUIPMENT:MECHANICAL:INTEGRATED JACK/LEVELER/STABILIZER

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THESE VEHICLES HAVE JACKING INSTRUCTIONS WHICH, IF FOLLOWED, COULD CAUSE THE VEHICLE OPERATOR TO PLACE THE JACK ON A FRAME WELD WHEN ATTEMPTING TO RAISE A REAR WHEEL. IF THE VEHICLE IS JACKED UP WITH THE JACK PLACED ON THE FRAME WELD AND IF THE VEHICLE IS FREE TO ROLL (WHEELS NOT BLOCKED OR CHOCKED), THE JACK COULD YIELD AND THE VEHICLE MAY DROP SUDDENLY.

Risk: IF THIS OCCURS AND ANY PORTION OF THE OPERATOR'S BODY IS UNDER THE VEHICLE, THE POTENTIAL FOR PERSONAL INJURY EXISTS.

Remedy: OWNERS WILL BE PROVIDED WITH A REVISED JACK INSTRUCTION AND STOWAGE CARD AND JACK WARNING LABEL, AS WELL AS A SUPPLEMENT TO THE OWNER GUIDE.

EQUIPMENT:MECHANICAL:INTEGRATED JACK/LEVELER/STABILIZER

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THESE VEHICLES HAVE JACKING INSTRUCTIONS WHICH, IF FOLLOWED, COULD CAUSE THE VEHICLE OPERATOR TO PLACE THE JACK ON A FRAME WELD WHEN ATTEMPTING TO RAISE A REAR WHEEL. IF THE VEHICLE IS JACKED UP WITH THE JACK PLACED ON THE FRAME WELD AND IF THE VEHICLE IS FREE TO ROLL (WHEELS NOT BLOCKED OR CHOCKED), THE JACK COULD YIELD AND THE VEHICLE MAY DROP SUDDENLY.

Risk: IF THIS OCCURS AND ANY PORTION OF THE OPERATOR'S BODY IS UNDER THE VEHICLE, THE POTENTIAL FOR PERSONAL INJURY EXISTS.

Remedy: OWNERS WILL BE PROVIDED WITH A REVISED JACK INSTRUCTION AND STOWAGE CARD AND JACK WARNING LABEL, AS WELL AS A SUPPLEMENT TO THE OWNER GUIDE.

EQUIPMENT:MECHANICAL:INTEGRATED JACK/LEVELER/STABILIZER

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THESE VEHICLES HAVE JACKING INSTRUCTIONS WHICH, IF FOLLOWED, COULD CAUSE THE VEHICLE OPERATOR TO PLACE THE JACK ON A FRAME WELD WHEN ATTEMPTING TO RAISE A REAR WHEEL. IF THE VEHICLE IS JACKED UP WITH THE JACK PLACED ON THE FRAME WELD AND IF THE VEHICLE IS FREE TO ROLL (WHEELS NOT BLOCKED OR CHOCKED), THE JACK COULD YIELD AND THE VEHICLE MAY DROP SUDDENLY.

Risk: IF THIS OCCURS AND ANY PORTION OF THE OPERATOR'S BODY IS UNDER THE VEHICLE, THE POTENTIAL FOR PERSONAL INJURY EXISTS.

Remedy: OWNERS WILL BE PROVIDED WITH A REVISED JACK INSTRUCTION AND STOWAGE CARD AND JACK WARNING LABEL, AS WELL AS A SUPPLEMENT TO THE OWNER GUIDE.

SEAT BELTS:FRONT:ANCHORAGE

VEHICLE DESCRIPTION: PASSENGER VEHICLES USING AFTERMARKET FRONT PASSENGER SIDE SEAT BELT ASSEMBLIES THAT WERE SOLD BY FORD PARTS DEPARTMENTS FROM JANUARY 1, THROUGH JUNE 13, 2000. THESE SEAT BELT ASSEMBLIES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." THE EQUIPMENT INVOLVED IS SERVICE STOCK SEAT BELT ASSEMBLIES, MODEL NOS. H 9977, H 9979, T 9063, AND T 9217, BUILT BY TRW VEHICLE SAFETY SYSTEMS, INC. (TRW) MANUFACTURED FROM JUNE 1, 1998 THROUGH MAY 21, 2000. SOME OF THESE SEAT BELT ASSEMBLIES MAY HAVE BEEN INSTALLED AS SERVICE REPLACEMENT EQUIPMENT ON THE VEHICLES INVOLVED IN THE RECALL.

Risk: IN THE EVENT OF A COLLISION, THESE SEAT BELTS MAY NOT RESTRAIN AN OCCUPANT INCREASING THE RISK OF INJURY.

Remedy: DEALERS WILL INSPECT THESE VEHICLES AND REPLACE THE SERVICE SEAT BELT ASSEMBLIES THAT WERE INSTALLED IN THESE VEHICLES FROM JANUARY 1 THROUGH JUNE 13, 2000.

SEAT BELTS:FRONT:ANCHORAGE

VEHICLE DESCRIPTION: PASSENGER VEHICLES USING AFTERMARKET DRIVER'S SEAT BELT ASSEMBLIES THAT WERE SOLD BY FORD PARTS DEPARTMENTS FROM JANUARY 1, THROUGH JUNE 13, 2000. THESE SEAT BELT ASSEMBLIES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." THE EQUIPMENT INVOLVED IS SERVICE STOCK SEAT BELT ASSEMBLIES, MODEL NOS. H 9977, H 9979, T 9063, AND T 9217, BUILT BY TRW VEHICLE SAFETY SYSTEMS, INC. (TRW) MANUFACTURED FROM JUNE 1, 1998 THROUGH MAY 21, 2000. SOME OF THESE SEAT BELT ASSEMBLIES MAY HAVE BEEN INSTALLED AS SERVICE REPLACEMENT EQUIPMENT ON THE VEHICLES INVOLVED IN THE RECALL.

Risk: IN THE EVENT OF A COLLISION, THESE SEAT BELTS MAY NOT RESTRAIN AN OCCUPANT INCREASING THE RISK OF INJURY.

Remedy: DEALERS WILL INSPECT THESE VEHICLES AND REPLACE THE SERVICE SEAT BELT ASSEMBLIES THAT WERE INSTALLED IN THESE VEHICLES FROM JANUARY 1 THROUGH JUNE 13, 2000.

SEAT BELTS:FRONT:ANCHORAGE

VEHICLE DESCRIPTION: PASSENGER VEHICLES USING AFTERMARKET FRONT PASSENGER SIDE SEAT BELT ASSEMBLIES THAT WERE SOLD BY FORD PARTS DEPARTMENTS FROM JANUARY 1, THROUGH JUNE 13, 2000. THESE SEAT BELT ASSEMBLIES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." THE EQUIPMENT INVOLVED IS SERVICE STOCK SEAT BELT ASSEMBLIES, MODEL NOS. H 9977, H 9979, T 9063, AND T 9217, BUILT BY TRW VEHICLE SAFETY SYSTEMS, INC. (TRW) MANUFACTURED FROM JUNE 1, 1998 THROUGH MAY 21, 2000. SOME OF THESE SEAT BELT ASSEMBLIES MAY HAVE BEEN INSTALLED AS SERVICE REPLACEMENT EQUIPMENT ON THE VEHICLES INVOLVED IN THE RECALL.

Risk: IN THE EVENT OF A COLLISION, THESE SEAT BELTS MAY NOT RESTRAIN AN OCCUPANT INCREASING THE RISK OF INJURY.

Remedy: DEALERS WILL INSPECT THESE VEHICLES AND REPLACE THE SERVICE SEAT BELT ASSEMBLIES THAT WERE INSTALLED IN THESE VEHICLES FROM JANUARY 1 THROUGH JUNE 13, 2000.

SEAT BELTS:FRONT:ANCHORAGE

VEHICLE DESCRIPTION: PASSENGER VEHICLES USING AFTERMARKET DRIVER'S SEAT BELT ASSEMBLIES THAT WERE SOLD BY FORD PARTS DEPARTMENTS FROM JANUARY 1, THROUGH JUNE 13, 2000. THESE SEAT BELT ASSEMBLIES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." THE EQUIPMENT INVOLVED IS SERVICE STOCK SEAT BELT ASSEMBLIES, MODEL NOS. H 9977, H 9979, T 9063, AND T 9217, BUILT BY TRW VEHICLE SAFETY SYSTEMS, INC. (TRW) MANUFACTURED FROM JUNE 1, 1998 THROUGH MAY 21, 2000. SOME OF THESE SEAT BELT ASSEMBLIES MAY HAVE BEEN INSTALLED AS SERVICE REPLACEMENT EQUIPMENT ON THE VEHICLES INVOLVED IN THE RECALL.

Risk: IN THE EVENT OF A COLLISION, THESE SEAT BELTS MAY NOT RESTRAIN AN OCCUPANT INCREASING THE RISK OF INJURY.

Remedy: DEALERS WILL INSPECT THESE VEHICLES AND REPLACE THE SERVICE SEAT BELT ASSEMBLIES THAT WERE INSTALLED IN THESE VEHICLES FROM JANUARY 1 THROUGH JUNE 13, 2000.

SEAT BELTS:FRONT:ANCHORAGE

VEHICLE DESCRIPTION: PASSENGER VEHICLES USING AFTERMARKET FRONT PASSENGER SIDE SEAT BELT ASSEMBLIES THAT WERE SOLD BY FORD PARTS DEPARTMENTS FROM JANUARY 1, THROUGH JUNE 13, 2000. THESE SEAT BELT ASSEMBLIES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." THE EQUIPMENT INVOLVED IS SERVICE STOCK SEAT BELT ASSEMBLIES, MODEL NOS. H 9977, H 9979, T 9063, AND T 9217, BUILT BY TRW VEHICLE SAFETY SYSTEMS, INC. (TRW) MANUFACTURED FROM JUNE 1, 1998 THROUGH MAY 21, 2000. SOME OF THESE SEAT BELT ASSEMBLIES MAY HAVE BEEN INSTALLED AS SERVICE REPLACEMENT EQUIPMENT ON THE VEHICLES INVOLVED IN THE RECALL.

Risk: IN THE EVENT OF A COLLISION, THESE SEAT BELTS MAY NOT RESTRAIN AN OCCUPANT INCREASING THE RISK OF INJURY.

Remedy: DEALERS WILL INSPECT THESE VEHICLES AND REPLACE THE SERVICE SEAT BELT ASSEMBLIES THAT WERE INSTALLED IN THESE VEHICLES FROM JANUARY 1 THROUGH JUNE 13, 2000.

SEAT BELTS:FRONT:ANCHORAGE

VEHICLE DESCRIPTION: PASSENGER VEHICLES USING AFTERMARKET DRIVER'S SEAT BELT ASSEMBLIES THAT WERE SOLD BY FORD PARTS DEPARTMENTS FROM JANUARY 1, THROUGH JUNE 13, 2000. THESE SEAT BELT ASSEMBLIES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." THE EQUIPMENT INVOLVED IS SERVICE STOCK SEAT BELT ASSEMBLIES, MODEL NOS. H 9977, H 9979, T 9063, AND T 9217, BUILT BY TRW VEHICLE SAFETY SYSTEMS, INC. (TRW) MANUFACTURED FROM JUNE 1, 1998 THROUGH MAY 21, 2000. SOME OF THESE SEAT BELT ASSEMBLIES MAY HAVE BEEN INSTALLED AS SERVICE REPLACEMENT EQUIPMENT ON THE VEHICLES INVOLVED IN THE RECALL.

Risk: IN THE EVENT OF A COLLISION, THESE SEAT BELTS MAY NOT RESTRAIN AN OCCUPANT INCREASING THE RISK OF INJURY.

Remedy: DEALERS WILL INSPECT THESE VEHICLES AND REPLACE THE SERVICE SEAT BELT ASSEMBLIES THAT WERE INSTALLED IN THESE VEHICLES FROM JANUARY 1 THROUGH JUNE 13, 2000.

SEAT BELTS:FRONT:ANCHORAGE

VEHICLE DESCRIPTION: PASSENGER VEHICLES USING AFTERMARKET FRONT PASSENGER SIDE SEAT BELT ASSEMBLIES THAT WERE SOLD BY FORD PARTS DEPARTMENTS FROM JANUARY 1, THROUGH JUNE 13, 2000. THESE SEAT BELT ASSEMBLIES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." THE EQUIPMENT INVOLVED IS SERVICE STOCK SEAT BELT ASSEMBLIES, MODEL NOS. H 9977, H 9979, T 9063, AND T 9217, BUILT BY TRW VEHICLE SAFETY SYSTEMS, INC. (TRW) MANUFACTURED FROM JUNE 1, 1998 THROUGH MAY 21, 2000. SOME OF THESE SEAT BELT ASSEMBLIES MAY HAVE BEEN INSTALLED AS SERVICE REPLACEMENT EQUIPMENT ON THE VEHICLES INVOLVED IN THE RECALL.

Risk: IN THE EVENT OF A COLLISION, THESE SEAT BELTS MAY NOT RESTRAIN AN OCCUPANT INCREASING THE RISK OF INJURY.

Remedy: DEALERS WILL INSPECT THESE VEHICLES AND REPLACE THE SERVICE SEAT BELT ASSEMBLIES THAT WERE INSTALLED IN THESE VEHICLES FROM JANUARY 1 THROUGH JUNE 13, 2000.

SEAT BELTS:FRONT:ANCHORAGE

VEHICLE DESCRIPTION: PASSENGER VEHICLES USING AFTERMARKET DRIVER'S SEAT BELT ASSEMBLIES THAT WERE SOLD BY FORD PARTS DEPARTMENTS FROM JANUARY 1, THROUGH JUNE 13, 2000. THESE SEAT BELT ASSEMBLIES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." THE EQUIPMENT INVOLVED IS SERVICE STOCK SEAT BELT ASSEMBLIES, MODEL NOS. H 9977, H 9979, T 9063, AND T 9217, BUILT BY TRW VEHICLE SAFETY SYSTEMS, INC. (TRW) MANUFACTURED FROM JUNE 1, 1998 THROUGH MAY 21, 2000. SOME OF THESE SEAT BELT ASSEMBLIES MAY HAVE BEEN INSTALLED AS SERVICE REPLACEMENT EQUIPMENT ON THE VEHICLES INVOLVED IN THE RECALL.

Risk: IN THE EVENT OF A COLLISION, THESE SEAT BELTS MAY NOT RESTRAIN AN OCCUPANT INCREASING THE RISK OF INJURY.

Remedy: DEALERS WILL INSPECT THESE VEHICLES AND REPLACE THE SERVICE SEAT BELT ASSEMBLIES THAT WERE INSTALLED IN THESE VEHICLES FROM JANUARY 1 THROUGH JUNE 13, 2000.

SEAT BELTS:FRONT:ANCHORAGE

VEHICLE DESCRIPTION: PASSENGER VEHICLES USING AFTERMARKET FRONT PASSENGER SIDE SEAT BELT ASSEMBLIES THAT WERE SOLD BY FORD PARTS DEPARTMENTS FROM JANUARY 1, THROUGH JUNE 13, 2000. THESE SEAT BELT ASSEMBLIES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." THE EQUIPMENT INVOLVED IS SERVICE STOCK SEAT BELT ASSEMBLIES, MODEL NOS. H 9977, H 9979, T 9063, AND T 9217, BUILT BY TRW VEHICLE SAFETY SYSTEMS, INC. (TRW) MANUFACTURED FROM JUNE 1, 1998 THROUGH MAY 21, 2000. SOME OF THESE SEAT BELT ASSEMBLIES MAY HAVE BEEN INSTALLED AS SERVICE REPLACEMENT EQUIPMENT ON THE VEHICLES INVOLVED IN THE RECALL.

Risk: IN THE EVENT OF A COLLISION, THESE SEAT BELTS MAY NOT RESTRAIN AN OCCUPANT INCREASING THE RISK OF INJURY.

Remedy: DEALERS WILL INSPECT THESE VEHICLES AND REPLACE THE SERVICE SEAT BELT ASSEMBLIES THAT WERE INSTALLED IN THESE VEHICLES FROM JANUARY 1 THROUGH JUNE 13, 2000.

SEAT BELTS:FRONT:ANCHORAGE

VEHICLE DESCRIPTION: PASSENGER VEHICLES USING AFTERMARKET DRIVER'S SEAT BELT ASSEMBLIES THAT WERE SOLD BY FORD PARTS DEPARTMENTS FROM JANUARY 1, THROUGH JUNE 13, 2000. THESE SEAT BELT ASSEMBLIES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." THE EQUIPMENT INVOLVED IS SERVICE STOCK SEAT BELT ASSEMBLIES, MODEL NOS. H 9977, H 9979, T 9063, AND T 9217, BUILT BY TRW VEHICLE SAFETY SYSTEMS, INC. (TRW) MANUFACTURED FROM JUNE 1, 1998 THROUGH MAY 21, 2000. SOME OF THESE SEAT BELT ASSEMBLIES MAY HAVE BEEN INSTALLED AS SERVICE REPLACEMENT EQUIPMENT ON THE VEHICLES INVOLVED IN THE RECALL.

Risk: IN THE EVENT OF A COLLISION, THESE SEAT BELTS MAY NOT RESTRAIN AN OCCUPANT INCREASING THE RISK OF INJURY.

Remedy: DEALERS WILL INSPECT THESE VEHICLES AND REPLACE THE SERVICE SEAT BELT ASSEMBLIES THAT WERE INSTALLED IN THESE VEHICLES FROM JANUARY 1 THROUGH JUNE 13, 2000.

ELECTRICAL SYSTEM

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE SPEED CONTROL DEACTIVATION SWITCH CAN DEVELOP A RESISTIVE SHORT IN THE ELECTRICAL CIRCUIT THAT COULD POTENTIALLY RESULT IN AN UNDERHOOD FIRE. A FIRE IS POSSIBLE BOTH WHEN THE VEHICLE IS RUNNING AND WHEN THE VEHICLE ENGINE IS OFF. ALSO, THE SHORT COULD DISABLE THE SPEED CONTROL SYSTEM OR CAUSE THE BRAKE LIGHT FUSE TO OPEN.

Risk: A FIRE CAN ORIGINATE IN THE LEFT FRONT UNDERHOOD AREA.

Remedy: DEALERS WILL INSTALL A NEW SPEED CONTROL DEACTIVATION SWITCH AND CONNECTOR SHELL. OWNER NOTIFICATION BEGAN MAY 20, 1999.

ELECTRICAL SYSTEM

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE SPEED CONTROL DEACTIVATION SWITCH CAN DEVELOP A RESISTIVE SHORT IN THE ELECTRICAL CIRCUIT THAT COULD POTENTIALLY RESULT IN AN UNDERHOOD FIRE. A FIRE IS POSSIBLE BOTH WHEN THE VEHICLE IS RUNNING AND WHEN THE VEHICLE ENGINE IS OFF. ALSO, THE SHORT COULD DISABLE THE SPEED CONTROL SYSTEM OR CAUSE THE BRAKE LIGHT FUSE TO OPEN.

Risk: A FIRE CAN ORIGINATE IN THE LEFT FRONT UNDERHOOD AREA.

Remedy: DEALERS WILL INSTALL A NEW SPEED CONTROL DEACTIVATION SWITCH AND CONNECTOR SHELL. OWNER NOTIFICATION BEGAN MAY 20, 1999.

SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT

VEHICLE DESCRIPTION: CERTAIN 1996-1999 FORD CROWN VICTORIA POLICE, FLEET, NATURAL GAS, AND 1996-1999 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT WERE PRODUCED WITH A LOWER CONTROL ARM BALL JOINT CONTAINING A ONE PIECE BEARING; AND 1990-1996 FORD CROWN VICTORIA POLICE, FLEET, AND NGV VEHICLES AND 1990-1996 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT HAVE BEEN SERVICED WITH EITHER A BALL JOINT CONTAINING THE ONE-PIECE BEARING OR A FRONT LOWER CONTROL ARM CONTAINING A BALL JOINT WITH A ONE-PIECE BEARING. THE ONE-PIECE BEARING WITHIN THE LOWER CONTROL ARM BALL JOINT CAN WEAKEN SLOWLY DURING USE AND EVENTUALLY CRACK. THIS COULD RESULT IN SEPARATION OF THE BALL AND CAP OF THE JOINT, ALLOWING THE CONTROL ARM TO DROP TO THE GROUND.

Risk: IF THIS OCCURS WHILE THE VEHICLE IS MOVING, REDUCED STEERING CONTROL COULD OCCUR, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL REPLACE THE LOWER CONTROL ARM BALL JOINTS (2).

SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT

VEHICLE DESCRIPTION: CERTAIN 1996-1999 FORD CROWN VICTORIA POLICE, FLEET, NATURAL GAS, AND 1996-1999 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT WERE PRODUCED WITH A LOWER CONTROL ARM BALL JOINT CONTAINING A ONE PIECE BEARING; AND 1990-1996 FORD CROWN VICTORIA POLICE, FLEET, AND NGV VEHICLES AND 1990-1996 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT HAVE BEEN SERVICED WITH EITHER A BALL JOINT CONTAINING THE ONE-PIECE BEARING OR A FRONT LOWER CONTROL ARM CONTAINING A BALL JOINT WITH A ONE-PIECE BEARING. THE ONE-PIECE BEARING WITHIN THE LOWER CONTROL ARM BALL JOINT CAN WEAKEN SLOWLY DURING USE AND EVENTUALLY CRACK. THIS COULD RESULT IN SEPARATION OF THE BALL AND CAP OF THE JOINT, ALLOWING THE CONTROL ARM TO DROP TO THE GROUND.

Risk: IF THIS OCCURS WHILE THE VEHICLE IS MOVING, REDUCED STEERING CONTROL COULD OCCUR, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL REPLACE THE LOWER CONTROL ARM BALL JOINTS (2).

SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT

VEHICLE DESCRIPTION: CERTAIN 1996-1999 FORD CROWN VICTORIA POLICE, FLEET, NATURAL GAS, AND 1996-1999 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT WERE PRODUCED WITH A LOWER CONTROL ARM BALL JOINT CONTAINING A ONE PIECE BEARING; AND 1990-1996 FORD CROWN VICTORIA POLICE, FLEET, AND NGV VEHICLES AND 1990-1996 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT HAVE BEEN SERVICED WITH EITHER A BALL JOINT CONTAINING THE ONE-PIECE BEARING OR A FRONT LOWER CONTROL ARM CONTAINING A BALL JOINT WITH A ONE-PIECE BEARING. THE ONE-PIECE BEARING WITHIN THE LOWER CONTROL ARM BALL JOINT CAN WEAKEN SLOWLY DURING USE AND EVENTUALLY CRACK. THIS COULD RESULT IN SEPARATION OF THE BALL AND CAP OF THE JOINT, ALLOWING THE CONTROL ARM TO DROP TO THE GROUND.

Risk: IF THIS OCCURS WHILE THE VEHICLE IS MOVING, REDUCED STEERING CONTROL COULD OCCUR, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL REPLACE THE LOWER CONTROL ARM BALL JOINTS (2).

SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT

VEHICLE DESCRIPTION: CERTAIN 1996-1999 FORD CROWN VICTORIA POLICE, FLEET, NATURAL GAS, AND 1996-1999 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT WERE PRODUCED WITH A LOWER CONTROL ARM BALL JOINT CONTAINING A ONE PIECE BEARING; AND 1990-1996 FORD CROWN VICTORIA POLICE, FLEET, AND NGV VEHICLES AND 1990-1996 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT HAVE BEEN SERVICED WITH EITHER A BALL JOINT CONTAINING THE ONE-PIECE BEARING OR A FRONT LOWER CONTROL ARM CONTAINING A BALL JOINT WITH A ONE-PIECE BEARING. THE ONE-PIECE BEARING WITHIN THE LOWER CONTROL ARM BALL JOINT CAN WEAKEN SLOWLY DURING USE AND EVENTUALLY CRACK. THIS COULD RESULT IN SEPARATION OF THE BALL AND CAP OF THE JOINT, ALLOWING THE CONTROL ARM TO DROP TO THE GROUND.

Risk: IF THIS OCCURS WHILE THE VEHICLE IS MOVING, REDUCED STEERING CONTROL COULD OCCUR, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL REPLACE THE LOWER CONTROL ARM BALL JOINTS (2).

SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT

VEHICLE DESCRIPTION: CERTAIN 1996-1999 FORD CROWN VICTORIA POLICE, FLEET, NATURAL GAS, AND 1996-1999 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT WERE PRODUCED WITH A LOWER CONTROL ARM BALL JOINT CONTAINING A ONE PIECE BEARING; AND 1990-1996 FORD CROWN VICTORIA POLICE, FLEET, AND NGV VEHICLES AND 1990-1996 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT HAVE BEEN SERVICED WITH EITHER A BALL JOINT CONTAINING THE ONE-PIECE BEARING OR A FRONT LOWER CONTROL ARM CONTAINING A BALL JOINT WITH A ONE-PIECE BEARING. THE ONE-PIECE BEARING WITHIN THE LOWER CONTROL ARM BALL JOINT CAN WEAKEN SLOWLY DURING USE AND EVENTUALLY CRACK. THIS COULD RESULT IN SEPARATION OF THE BALL AND CAP OF THE JOINT, ALLOWING THE CONTROL ARM TO DROP TO THE GROUND.

Risk: IF THIS OCCURS WHILE THE VEHICLE IS MOVING, REDUCED STEERING CONTROL COULD OCCUR, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL REPLACE THE LOWER CONTROL ARM BALL JOINTS (2).

SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT

VEHICLE DESCRIPTION: CERTAIN 1996-1999 FORD CROWN VICTORIA POLICE, FLEET, NATURAL GAS, AND 1996-1999 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT WERE PRODUCED WITH A LOWER CONTROL ARM BALL JOINT CONTAINING A ONE PIECE BEARING; AND 1990-1996 FORD CROWN VICTORIA POLICE, FLEET, AND NGV VEHICLES AND 1990-1996 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT HAVE BEEN SERVICED WITH EITHER A BALL JOINT CONTAINING THE ONE-PIECE BEARING OR A FRONT LOWER CONTROL ARM CONTAINING A BALL JOINT WITH A ONE-PIECE BEARING. THE ONE-PIECE BEARING WITHIN THE LOWER CONTROL ARM BALL JOINT CAN WEAKEN SLOWLY DURING USE AND EVENTUALLY CRACK. THIS COULD RESULT IN SEPARATION OF THE BALL AND CAP OF THE JOINT, ALLOWING THE CONTROL ARM TO DROP TO THE GROUND.

Risk: IF THIS OCCURS WHILE THE VEHICLE IS MOVING, REDUCED STEERING CONTROL COULD OCCUR, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL REPLACE THE LOWER CONTROL ARM BALL JOINTS (2).

SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT

VEHICLE DESCRIPTION: CERTAIN 1996-1999 FORD CROWN VICTORIA POLICE, FLEET, NATURAL GAS, AND 1996-1999 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT WERE PRODUCED WITH A LOWER CONTROL ARM BALL JOINT CONTAINING A ONE PIECE BEARING; AND 1990-1996 FORD CROWN VICTORIA POLICE, FLEET, AND NGV VEHICLES AND 1990-1996 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT HAVE BEEN SERVICED WITH EITHER A BALL JOINT CONTAINING THE ONE-PIECE BEARING OR A FRONT LOWER CONTROL ARM CONTAINING A BALL JOINT WITH A ONE-PIECE BEARING. THE ONE-PIECE BEARING WITHIN THE LOWER CONTROL ARM BALL JOINT CAN WEAKEN SLOWLY DURING USE AND EVENTUALLY CRACK. THIS COULD RESULT IN SEPARATION OF THE BALL AND CAP OF THE JOINT, ALLOWING THE CONTROL ARM TO DROP TO THE GROUND.

Risk: IF THIS OCCURS WHILE THE VEHICLE IS MOVING, REDUCED STEERING CONTROL COULD OCCUR, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL REPLACE THE LOWER CONTROL ARM BALL JOINTS (2).

SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT

VEHICLE DESCRIPTION: CERTAIN 1996-1999 FORD CROWN VICTORIA POLICE, FLEET, NATURAL GAS, AND 1996-1999 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT WERE PRODUCED WITH A LOWER CONTROL ARM BALL JOINT CONTAINING A ONE PIECE BEARING; AND 1990-1996 FORD CROWN VICTORIA POLICE, FLEET, AND NGV VEHICLES AND 1990-1996 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT HAVE BEEN SERVICED WITH EITHER A BALL JOINT CONTAINING THE ONE-PIECE BEARING OR A FRONT LOWER CONTROL ARM CONTAINING A BALL JOINT WITH A ONE-PIECE BEARING. THE ONE-PIECE BEARING WITHIN THE LOWER CONTROL ARM BALL JOINT CAN WEAKEN SLOWLY DURING USE AND EVENTUALLY CRACK. THIS COULD RESULT IN SEPARATION OF THE BALL AND CAP OF THE JOINT, ALLOWING THE CONTROL ARM TO DROP TO THE GROUND.

Risk: IF THIS OCCURS WHILE THE VEHICLE IS MOVING, REDUCED STEERING CONTROL COULD OCCUR, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL REPLACE THE LOWER CONTROL ARM BALL JOINTS (2).

SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT

VEHICLE DESCRIPTION: CERTAIN 1996-1999 FORD CROWN VICTORIA POLICE, FLEET, NATURAL GAS, AND 1996-1999 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT WERE PRODUCED WITH A LOWER CONTROL ARM BALL JOINT CONTAINING A ONE PIECE BEARING; AND 1990-1996 FORD CROWN VICTORIA POLICE, FLEET, AND NGV VEHICLES AND 1990-1996 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT HAVE BEEN SERVICED WITH EITHER A BALL JOINT CONTAINING THE ONE-PIECE BEARING OR A FRONT LOWER CONTROL ARM CONTAINING A BALL JOINT WITH A ONE-PIECE BEARING. THE ONE-PIECE BEARING WITHIN THE LOWER CONTROL ARM BALL JOINT CAN WEAKEN SLOWLY DURING USE AND EVENTUALLY CRACK. THIS COULD RESULT IN SEPARATION OF THE BALL AND CAP OF THE JOINT, ALLOWING THE CONTROL ARM TO DROP TO THE GROUND.

Risk: IF THIS OCCURS WHILE THE VEHICLE IS MOVING, REDUCED STEERING CONTROL COULD OCCUR, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL REPLACE THE LOWER CONTROL ARM BALL JOINTS (2).

SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT

VEHICLE DESCRIPTION: CERTAIN 1996-1999 FORD CROWN VICTORIA POLICE, FLEET, NATURAL GAS, AND 1996-1999 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT WERE PRODUCED WITH A LOWER CONTROL ARM BALL JOINT CONTAINING A ONE PIECE BEARING; AND 1990-1996 FORD CROWN VICTORIA POLICE, FLEET, AND NGV VEHICLES AND 1990-1996 LINCOLN TOWN CAR LIMOUSINE VEHICLES THAT HAVE BEEN SERVICED WITH EITHER A BALL JOINT CONTAINING THE ONE-PIECE BEARING OR A FRONT LOWER CONTROL ARM CONTAINING A BALL JOINT WITH A ONE-PIECE BEARING. THE ONE-PIECE BEARING WITHIN THE LOWER CONTROL ARM BALL JOINT CAN WEAKEN SLOWLY DURING USE AND EVENTUALLY CRACK. THIS COULD RESULT IN SEPARATION OF THE BALL AND CAP OF THE JOINT, ALLOWING THE CONTROL ARM TO DROP TO THE GROUND.

Risk: IF THIS OCCURS WHILE THE VEHICLE IS MOVING, REDUCED STEERING CONTROL COULD OCCUR, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL REPLACE THE LOWER CONTROL ARM BALL JOINTS (2).

SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS

THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH FEDERAL REGULATION 573. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. FORD IS INITIATING AN OWNER NOTIFICATION PROGRAM FOR OWNERS OF CERTAIN 1995-1997 CROWN VICTORIA MODEL VEHICLES WITH POLICE, TAXI, AND COMMERCIAL FLEET PACKAGES AND TOWN CAR VEHICLES WITH THE LIVERY PACKAGE. THESE VEHICLES MAY HAVE INSUFFICIENT CLEARANCE BETWEEN THE BRAKE LINE AND THE UNDERBODY FRONT FLOOR PAN ASSEMBLY WHICH COULD CAUSE WEAR OF THE BRAKE LINES.

Risk: THIS COULD LEAD TO BRAKE FLUID LOSS FOR THE REAR BRAKES AND, POTENTIALLY, INCREASED STOPPING DISTANCES.

Remedy: DEALERS WILL INSPECT THE BRAKE LINES FOR WEAR, INSTALL TWO NEW TUBE BUNDLE CLIPS, AND CHECK THE BRAKE LINES FOR PROPER CLEARANCES. IF THE BRAKE LINES ARE WORN, THE DAMAGED SECTION OF THE BRAKE LINE WILL BE REPLACED.

SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS

THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH FEDERAL REGULATION 573. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. FORD IS INITIATING AN OWNER NOTIFICATION PROGRAM FOR OWNERS OF CERTAIN 1995-1997 CROWN VICTORIA MODEL VEHICLES WITH POLICE, TAXI, AND COMMERCIAL FLEET PACKAGES AND TOWN CAR VEHICLES WITH THE LIVERY PACKAGE. THESE VEHICLES MAY HAVE INSUFFICIENT CLEARANCE BETWEEN THE BRAKE LINE AND THE UNDERBODY FRONT FLOOR PAN ASSEMBLY WHICH COULD CAUSE WEAR OF THE BRAKE LINES.

Risk: THIS COULD LEAD TO BRAKE FLUID LOSS FOR THE REAR BRAKES AND, POTENTIALLY, INCREASED STOPPING DISTANCES.

Remedy: DEALERS WILL INSPECT THE BRAKE LINES FOR WEAR, INSTALL TWO NEW TUBE BUNDLE CLIPS, AND CHECK THE BRAKE LINES FOR PROPER CLEARANCES. IF THE BRAKE LINES ARE WORN, THE DAMAGED SECTION OF THE BRAKE LINE WILL BE REPLACED.

SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS

THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH FEDERAL REGULATION 573. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. FORD IS INITIATING AN OWNER NOTIFICATION PROGRAM FOR OWNERS OF CERTAIN 1995-1997 CROWN VICTORIA MODEL VEHICLES WITH POLICE, TAXI, AND COMMERCIAL FLEET PACKAGES AND TOWN CAR VEHICLES WITH THE LIVERY PACKAGE. THESE VEHICLES MAY HAVE INSUFFICIENT CLEARANCE BETWEEN THE BRAKE LINE AND THE UNDERBODY FRONT FLOOR PAN ASSEMBLY WHICH COULD CAUSE WEAR OF THE BRAKE LINES.

Risk: THIS COULD LEAD TO BRAKE FLUID LOSS FOR THE REAR BRAKES AND, POTENTIALLY, INCREASED STOPPING DISTANCES.

Remedy: DEALERS WILL INSPECT THE BRAKE LINES FOR WEAR, INSTALL TWO NEW TUBE BUNDLE CLIPS, AND CHECK THE BRAKE LINES FOR PROPER CLEARANCES. IF THE BRAKE LINES ARE WORN, THE DAMAGED SECTION OF THE BRAKE LINE WILL BE REPLACED.

EXTERIOR LIGHTING:HEADLIGHTS

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE TEXT AND/OR GRAPHICS FOR THE VEHICLE HEADLAMP AIMING INSTRUCTIONS PROVIDED IN THE OWNER GUIDES ARE NOT SUFFICIENTLY CLEAR. THIS DOES NOT MEET THE REQUIREMENTS OF FMVSS NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."

Risk: IF THE HEADLAMP ASSEMBLIES ARE REPLACED, CUSTOMERS MAY BE CONFUSED BY THE AIMING INSTRUCTIONS PROVIDED IN THE OWNER GUIDES CAUSING THE HEADLAMPS TO BE IMPROPERLY AIMED.

Remedy: OWNER GUIDES CONTAINING REVISED AIMING INSTRUCTIONS WILL BE MAILED TO OWNERS OF THESE VEHICLES.

AIR BAGS:FRONTAL

TWO BOLTS THAT ATTACH THE DRIVER AIR BAG TO THE STEERING WHEEL WERE NOT INSTALLED DURING VEHICLE ASSEMBLY.

Risk: IN THE EVENT OF A FRONTAL COLLISION, THE AIR BAG MODULE WOULD STAY IN POSITION DURING DEPLOYMENT. HOWEVER, THE MODULE COULD LEAVE THE STEERING WHEEL CAVITY FOLLOWING AIR BAG DEPLOYMENT.

Remedy: DEALERS WILL INSPECT THE VEHICLES AND INSTALL ANY BOLTS THAT ARE MISSING.

STEERING:LINKAGES

THE PITMAN ARMS WERE NOT FULLY LUBRICATED AT THE ASSEMBLY PLANT. THE "BALL JOINT" AT THE OUTER END OF THE PITMAN ARM CAN BECOME CONTAMINATED AND CORRODE.

Risk: SUCH CORROSION CAN RESULT IN ABNORMAL WEAR OF THE JOINT, RESULTING IN SEPARATION OF THE JOINT. LOSS OF STEERING CONTROL CAN OCCUR INCREASING THE RISK OF A VEHICLE ACCIDENT.

Remedy: DEALERS WILL INSPECT THE VEHICLES AND IF THE JOINT IS FOUND TO HAVE SIGNIFICANT WEAR, THE ARM WILL BE REPLACED. THOSE PITMAN ARMS NOT REPLACED WILL HAVE THE "BALL JOINT" FULLY GREASED.

STEERING:LINKAGES

THE PITMAN ARMS WERE NOT FULLY LUBRICATED AT THE ASSEMBLY PLANT. THE "BALL JOINT" AT THE OUTER END OF THE PITMAN ARM CAN BECOME CONTAMINATED AND CORRODE.

Risk: SUCH CORROSION CAN RESULT IN ABNORMAL WEAR OF THE JOINT, RESULTING IN SEPARATION OF THE JOINT. LOSS OF STEERING CONTROL CAN OCCUR INCREASING THE RISK OF A VEHICLE ACCIDENT.

Remedy: DEALERS WILL INSPECT THE VEHICLES AND IF THE JOINT IS FOUND TO HAVE SIGNIFICANT WEAR, THE ARM WILL BE REPLACED. THOSE PITMAN ARMS NOT REPLACED WILL HAVE THE "BALL JOINT" FULLY GREASED.

SEAT BELTS:REAR/OTHER

THE ELR/ALR FEATURE IS USED TO ACCOMMODATE CHILD RESTRAINTS. WHEN SERVICING THE REAR BELT ASSEMBLIES, WRONG PARTS COULD HAVE BEEN USED WHICH DO NOT CONTAIN THE AUTOMATIC LOCKING FEATURE.

Risk: IN THE EVENT OF AN ACCIDENT, THE SEAT BELT ASSEMBLIES MAY NOT PROPERLY SECURE THE CHILD RESTRAINT INCREASING THE RISK OF PERSONAL INJURY TO THE SEAT OCCUPANT.

Remedy: DEALERS WILL REPLACE THE REAR BELT ASSEMBLIES WITH THE APPROPRIATE DESIGN RETRACTOR AND TONGUE ASSEMBLIES.

ELECTRICAL SYSTEM:IGNITION

THE IGNITION SWITCH COULD EXPERIENCE AN INTERNAL SHORT CIRCUIT.

Risk: THIS CONDITION COULD CAUSE OVERHEATING, SMOKE, AND POSSIBLY FIRE IN THE STEERING COLUMN AREA OF THE VEHICLE.

Remedy: DEALERS WILL REPLACE THE IGNITION SWITCH.

ELECTRICAL SYSTEM:IGNITION

THE IGNITION SWITCH COULD EXPERIENCE AN INTERNAL SHORT CIRCUIT.

Risk: THIS CONDITION COULD CAUSE OVERHEATING, SMOKE, AND POSSIBLY FIRE IN THE STEERING COLUMN AREA OF THE VEHICLE.

Remedy: DEALERS WILL REPLACE THE IGNITION SWITCH.

LATCHES/LOCKS/LINKAGES:DOORS:LATCH

WHEN IN THE SECONDARY LATCHED POSITION, THE DRIVER DOOR LATCHES MAY OPEN WHEN SUBJECTED TO TRANSVERSE LOADS LESS THAN THAT SPECIFIED IN FMVSS NO. 206, "DOOR LOCKS AND DOOR RETENTION COMPONENTS."

Risk: THE DRIVER'S DOOR, WHEN CLOSED ONLY TO THE SECONDARY LATCHED POSITION, MAY NOT SUSTAIN A 1,000 POUND TRANSVERSE LOAD.

Remedy: DEALERS WILL INSPECT AND, IF NECESSARY, REPLACE THE DRIVER DOOR LATCH.

LATCHES/LOCKS/LINKAGES:HOOD:LATCH

THE SECONDARY HOOD LATCH MAY NOT ENGAGE WHEN THE HOOD IS CLOSED.

Risk: IN THE EVENT THE PRIMARY HOOD LATCH RELEASES OR IS NOT PROPERLY LATCHED WHEN THE VEHICLE IS IN MOTION, THE HOOD COULD FLY UP OBSTRUCTING THE OPERATOR'S VISION, AND INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.

Remedy: DEALERS WILL REPLACE THE HOOD LATCH ASSEMBLY.

LATCHES/LOCKS/LINKAGES:HOOD:LATCH

THE SECONDARY HOOD LATCH MAY NOT ENGAGE WHEN THE HOOD IS CLOSED.

Risk: IN THE EVENT THE PRIMARY HOOD LATCH RELEASES OR IS NOT PROPERLY LATCHED WHEN THE VEHICLE IS IN MOTION, THE HOOD COULD FLY UP OBSTRUCTING THE OPERATOR'S VISION, AND INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.

Remedy: DEALERS WILL REPLACE THE HOOD LATCH ASSEMBLY.

SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS

IMPROPER INSTALLATION OF THE REAR BRAKE LINE AT THE POINT AT WHICH THE EXTENDED BRAKE LINE FIRST BENDS AND EXTENDS OVER THE LEFT REAR WHEEL AREA OF THE FRAME. IF NOT INSTALLED WITH SUFFICIENT CLEARANCE, CHAFING OF THE BRAKE LINE CAN OCCUR IN AN AREA ADJACENT TO THE REAR FLOOR PAN.

Risk: THE REAR BRAKE LINE CAN LEAK OR RUPTURE RESULTING IN REDUCED BRAKING CAPABILITY, LOSS OF REAR BRAKES, AND/OR LOSS OF BRAKE FLUID RESERVES IN THE MASTER BRAKE CYLINDER.

Remedy: DEALERS WILL INSPECT THE BRAKE LINE FOR PROPER INSTALLATION AND/OR DAMAGE AND REPLACE AS NECESSARY. ALSO A PROTECTIVE BOOT OR SLEEVE OVER THE BRAKE LINE WILL BE INSTALLED.

SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS

IMPROPER INSTALLATION OF THE REAR BRAKE LINE AT THE POINT AT WHICH THE EXTENDED BRAKE LINE FIRST BENDS AND EXTENDS OVER THE LEFT REAR WHEEL AREA OF THE FRAME. IF NOT INSTALLED WITH SUFFICIENT CLEARANCE, CHAFING OF THE BRAKE LINE CAN OCCUR IN AN AREA ADJACENT TO THE REAR FLOOR PAN.

Risk: THE REAR BRAKE LINE CAN LEAK OR RUPTURE RESULTING IN REDUCED BRAKING CAPABILITY, LOSS OF REAR BRAKES, AND/OR LOSS OF BRAKE FLUID RESERVES IN THE MASTER BRAKE CYLINDER.

Remedy: DEALERS WILL INSPECT THE BRAKE LINE FOR PROPER INSTALLATION AND/OR DAMAGE AND REPLACE AS NECESSARY. ALSO A PROTECTIVE BOOT OR SLEEVE OVER THE BRAKE LINE WILL BE INSTALLED.

SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS

IMPROPER INSTALLATION OF THE REAR BRAKE LINE AT THE POINT AT WHICH THE EXTENDED BRAKE LINE FIRST BENDS AND EXTENDS OVER THE LEFT REAR WHEEL AREA OF THE FRAME. IF NOT INSTALLED WITH SUFFICIENT CLEARANCE, CHAFING OF THE BRAKE LINE CAN OCCUR IN AN AREA ADJACENT TO THE REAR FLOOR PAN.

Risk: THE REAR BRAKE LINE CAN LEAK OR RUPTURE RESULTING IN REDUCED BRAKING CAPABILITY, LOSS OF REAR BRAKES, AND/OR LOSS OF BRAKE FLUID RESERVES IN THE MASTER BRAKE CYLINDER.

Remedy: DEALERS WILL INSPECT THE BRAKE LINE FOR PROPER INSTALLATION AND/OR DAMAGE AND REPLACE AS NECESSARY. ALSO A PROTECTIVE BOOT OR SLEEVE OVER THE BRAKE LINE WILL BE INSTALLED.

LATCHES/LOCKS/LINKAGES:HOOD:LATCH

CORROSION OF THE HOOD LATCH STRIKER PLATE CAUSES DETACHMENT OF THE PLATE FROM THE HOOD ASSEMBLY RESULTING IN AN UNEXPECTED OPENING OF THE HOOD WHILE THE VEHICLE IS BEING DRIVEN.

Risk: THIS CONDITION CAN REDUCE THE DRIVER'S VIEW OF THE ROAD INCREASING THE POTENTIAL OF A VEHICLE ACCIDENT.

Remedy: DEALERS WILL INSTALL A NEW HOOD INNER PANEL REINFORCEMENT AND A NEW, GALVANIZED HOOD LATCH STRIKER PLATE.

LATCHES/LOCKS/LINKAGES:HOOD:LATCH

CORROSION OF THE HOOD LATCH STRIKER PLATE CAUSES DETACHMENT OF THE PLATE FROM THE HOOD ASSEMBLY RESULTING IN AN UNEXPECTED OPENING OF THE HOOD WHILE THE VEHICLE IS BEING DRIVEN.

Risk: THIS CONDITION CAN REDUCE THE DRIVER'S VIEW OF THE ROAD INCREASING THE POTENTIAL OF A VEHICLE ACCIDENT.

Remedy: DEALERS WILL INSTALL A NEW HOOD INNER PANEL REINFORCEMENT AND A NEW, GALVANIZED HOOD LATCH STRIKER PLATE.

FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP

THE SEAL MATERIAL BETWEEN THE FUEL FILLER PIPE AND FUEL TANK MAY NOT HAVE BEEN FULLY CURED DURING THE MOLDING PROCESS WHICH COULD ALLOW FOR FUEL LEAKAGE.

Risk: FUEL LEAKAGE COULD RESULT IN A VEHICLE FIRE IF AN IGNITION SOURCE WERE PRESENT.

Remedy: DEALERS WILL REPLACE THE FUEL FILLER PIPE-TO-FUEL TANK SEAL WITH A NEW SEAL OF DIFFERENT MATERIAL.

AIR BAGS:FRONTAL

THE PASSENGER SIDE AIR BAG HAS AN INFLATOR BODY THAT CRACKED DURING FORMING OF THE CURL THAT RETAINS THE IGNITER PLUG IN THE END OF THE INFLATOR. ALSO THE IGNITER END CAP CAN SEPARATE FROM THE INFLATOR.

Risk: THE PASSENGER SIDE AIR BAG MAY NOT INFLATE PROPERLY RESULTING IN REDUCED OCCUPANT PROTECTION IN A VEHICLE ACCIDENT. IF THE IGNITER END CAP SEPARATES IN A FRONTAL COLLISION, HOT GASES CAN BE RELEASED AND IGNITE FLAMMABLE MATERIAL OR CAUSE BURN INJURIES.

Remedy: DEALERS WILL REMOVE AND REPLACE THE PASSENGER SIDE AIR BAG MODULE.

SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS

THE NUTS AND BOLTS THAT ATTACH THE REAR BRAKE ADAPTOR TO THE AXLE HOUSING FLANGE CAN LOOSEN AND EVENTUALLY SEPARATE. IF ONE OR MORE OF THE NUTS COME OFF THE BOLTS, DAMAGE TO THE PARKING BRAKE ASSEMBLY OR TO THE ANTILOCK BRAKE SYSTEM (ABS) SENSOR AND SENSOR RING (IF SO EQUIPPED) WILL OCCUR. IF ALL FOUR NUTS ON ONE END OF THE AXLE COME OFF THE BOLTS, DAMAGE TO THE BRAKE HYDRAULIC LINE OR THE PARKING BRAKE CABLE CAN OCCUR.

Risk: OCCURRENCE OF ANY OF THESE CONDITIONS CAN RESULT IN A LOSS OF BRAKING CAPABILITY AND POSSIBLE ACCIDENT.

Remedy: DEALERS WILL INSPECT AND, IF NEEDED, INSTALL NEW BOLTS. IF ANY OF THE FASTENERS ARE DISCONNECTED, THE PARKING BRAKE AND ABS COMPONENTS WILL BE INSPECTED AND SERVICED.

SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES

THE BRAKE PEDAL PUSH ROD RETAINER (HAIRPIN CLIP) MAY BE MISSING OR NOT PROPERLY INSTALLED ON THE SERVICE BRAKE PEDAL. THIS CAN CAUSE DISENGAGEMENT OF THE BRAKE PUSHROD AND LOSS OF BRAKING ABILITY.

Risk: LOSS OF BRAKING ABILITY CAN RESULT IN A VEHICLE ACCIDENT.

Remedy: DEALERS WILL INSPECT AND, IF NECESSARY, REPLACE THE RETAINER.

LATCHES/LOCKS/LINKAGES:HOOD:LATCH

THE SECONDARY HOOD LATCH MAY NOT ENGAGE WHEN THE HOOD IS CLOSED.

Risk: IN THE EVENT THE PRIMARY HOOD LATCH RELEASES WHEN THEVEHICLE IS IN MOTION, THE HOOD COULD FLY UP, OBSTRUCTING THE OPERATOR'S VISION,AND INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.

Remedy: INSTALL A NEW HOOD LATCHING ASSEMBLY.

FUEL SYSTEM, GASOLINE:DELIVERY

DISTORTED FUEL LINES IN ENGINE COMPARTMENT MAY CONTACT THE STEERING COLUMN UNIVERSAL JOINT AND CAUSE DAMAGE TO THE FUEL LINE.

Risk: FUEL LEAKAGE COULD OCCUR FROM THE DAMAGED FLUID LINE AND,IN THE PRESENCE OF AN IGNITION SOURCE, COULD RESULT IN A FIRE.

Remedy: REPOSITION FUEL LINE TO PREVENT CONTACT WITH UNIVERSAL JOINT; IF FUEL LINES ARE ALREADY DAMAGED, REPAIR OR REPLACE FUEL LINES.

EQUIPMENT:OTHER:LABELS

GROSS VEHICLE WEIGHT RATINGS AND TIRE INFORMATION MAY BE INCORRECT ON LABELS.

Risk: VEHICLES WOULD NOT COMPLY WITH 49 CFR PART 567.

Remedy: INSTALL REVISED CERTIFICATION LABELS.

EQUIPMENT:OTHER:LABELS

TIRE PLACARD MAY CONTAIN INCORRECT GROSS VEHICLE WEIGHT RATINGS AND TIRE INFORMATION.

Risk: LIMOUSINES WOULD NOT COMPLY WITH FMVSS 110 AND CONSUMERMIGHT UNKNOWINGLY OVERLOAD THE VEHICLE BECAUSE OF PLACARD MISINFORMATION.

Remedy: INSTALL REVISED TIRE PLACARDS.

EQUIPMENT:OTHER:LABELS

GROSS VEHICLE WEIGHT RATINGS AND TIRE INFORMATION MAY BE INCORRECT ON LABELS.

Risk: VEHICLES WOULD NOT COMPLY WITH 49 CFR PART 567.

Remedy: INSTALL REVISED CERTIFICATION LABELS.

EQUIPMENT:OTHER:LABELS

TIRE PLACARD MAY CONTAIN INCORRECT GROSS VEHICLE WEIGHT RATINGS AND TIRE INFORMATION.

Risk: LIMOUSINES WOULD NOT COMPLY WITH FMVSS 110 AND CONSUMERMIGHT UNKNOWINGLY OVERLOAD THE VEHICLE BECAUSE OF PLACARD MISINFORMATION.

Remedy: INSTALL REVISED TIRE PLACARDS.

EQUIPMENT:OTHER:LABELS

VEHICLE DESCRIPTION: LIMOUSINES BUILT BY EMPIRE COACH. VEHICLE ALTERERS LABEL MAY BE MISSING OR INCOMPLETE.

Risk: VEHICLES DO NOT COMPLY WITH PART 567.

Remedy: ADD COMPLIANCE LABEL.

EQUIPMENT:OTHER:LABELS

VEHICLE DESCRIPTION: LIMOUSINES BUILT BY EMPIRE COACH. VEHICLE ALTERERS LABEL MAY BE MISSING OR INCOMPLETE.

Risk: VEHICLES DO NOT COMPLY WITH PART 567.

Remedy: ADD COMPLIANCE LABEL.

EQUIPMENT:OTHER:LABELS

VEHICLE DESCRIPTION: LIMOUSINES BUILT BY EMPIRE COACH. VEHICLE ALTERERS LABEL MAY BE MISSING OR INCOMPLETE.

Risk: VEHICLES DO NOT COMPLY WITH PART 567.

Remedy: ADD COMPLIANCE LABEL.

EQUIPMENT:OTHER:LABELS

VEHICLE DESCRIPTION: LIMOUSINES BUILT BY EMPIRE COACH. VEHICLE ALTERERS LABEL MAY BE MISSING OR INCOMPLETE.

Risk: VEHICLES DO NOT COMPLY WITH PART 567.

Remedy: ADD COMPLIANCE LABEL.

SEAT BELTS:FRONT:ANCHORAGE

SAFETY BELTS (TYPE 1 LAP BELTS) FOR REAR FACING SEATS WERE NOT INSTALLED.

Risk: LACK OF RESTRAINTS COULD CONTRIBUTE TO OTHERWISE PREVENTABLE INJURY AND WOULD NOT COMPLY WITH FMVSS 209 AND 210.

Remedy: INSTALL SAFETY BELTS FOR REAR FACING SEATS.

SEAT BELTS:FRONT:ANCHORAGE

SAFETY BELTS (TYPE 1 LAP BELTS) FOR REAR FACING SEATS WERE NOT INSTALLED.

Risk: LACK OF RESTRAINTS COULD CONTRIBUTE TO OTHERWISE PREVENTABLE INJURY AND WOULD NOT COMPLY WITH FMVSS 209 AND 210.

Remedy: INSTALL SAFETY BELTS FOR REAR FACING SEATS.

SEAT BELTS:FRONT:ANCHORAGE

SAFETY BELTS (TYPE 1 LAP BELTS) FOR REAR FACING SEATS WERE NOT INSTALLED.

Risk: LACK OF RESTRAINTS COULD CONTRIBUTE TO OTHERWISE PREVENTABLE INJURY AND WOULD NOT COMPLY WITH FMVSS 209 AND 210.

Remedy: INSTALL SAFETY BELTS FOR REAR FACING SEATS.

SEAT BELTS:FRONT:ANCHORAGE

SAFETY BELTS (TYPE 1 LAP BELTS) FOR REAR FACING SEATS WERE NOT INSTALLED.

Risk: LACK OF RESTRAINTS COULD CONTRIBUTE TO OTHERWISE PREVENTABLE INJURY AND WOULD NOT COMPLY WITH FMVSS 209 AND 210.

Remedy: INSTALL SAFETY BELTS FOR REAR FACING SEATS.

FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS

SPRING LOCK FUEL LINE COUPLING MAY NOT BE PROPERLY ENGAGED.

Risk: COUPLING COULD DISENGAGE DUE TO FUEL PRESSURE,VIBRATION, AND ENGINE MOVEMENTS; THIS WOULD CAUSE LOSS OF FUEL WHICH, INPRESENCE OF AN IGNITION SOURCE, CREATES A FIRE RISK.

Remedy: INSTALL RETAINER CLIPS OVER THE COUPLINGS TO PREVENT COUPLING SEPARATION AND FUEL LEAKAGE.

FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS

SPRING LOCK FUEL LINE COUPLING MAY NOT BE PROPERLY ENGAGED.

Risk: COUPLING COULD DISENGAGE DUE TO FUEL PRESSURE,VIBRATION, AND ENGINE MOVEMENTS; THIS WOULD CAUSE LOSS OF FUEL WHICH, INPRESENCE OF AN IGNITION SOURCE, CREATES A FIRE RISK.

Remedy: INSTALL RETAINER CLIPS OVER THE COUPLINGS TO PREVENT COUPLING SEPARATION AND FUEL LEAKAGE.

FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS

SPRING LOCK FUEL LINE COUPLING MAY NOT BE PROPERLY ENGAGED.

Risk: COUPLING COULD DISENGAGE DUE TO FUEL PRESSURE,VIBRATION, AND ENGINE MOVEMENTS; THIS WOULD CAUSE LOSS OF FUEL WHICH, INPRESENCE OF AN IGNITION SOURCE, CREATES A FIRE RISK.

Remedy: INSTALL RETAINER CLIPS OVER THE COUPLINGS TO PREVENT COUPLING SEPARATION AND FUEL LEAKAGE.

FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM

FUEL RAILS MAY BE BENT SO THAT NO. 5 INJECTOR CUPS ARE OUT OF DESIGN POSITION.

Risk: BENT FUEL RAIL COULD CAUSE A FUEL LEAK, WHICH INPRESENCE OF AN IGNITION SOURCE COULD RESULT IN AN ENGINE FIRE.

Remedy: REPLACE FUEL RAIL ASSEMBLIES AS NECESSARY.

STEERING:LINKAGES:ARM:IDLER AND ATTACHMENT

Risk: DRIVER WOULD EXPERIENCE A CLUNKING NOISE ON TURNS AND ALOOSE FEELING IN THE STEERING WHEEL; STEERING CONTROL WOULD BE MAINTAINED.

Remedy: REPLACE IDLER ARM ASSEMBLY.

STEERING:LINKAGES:ROD:RELAY:CONNECTING

STEERING CENTERLINKS MAY BREAK AT A BEND LOCATION.

Risk: STEERING CONTROL WOULD BE DIMINISHED, WITH REDUCEDCONTROL OF LEFT WHEEL ONLY AND CONSIDERABLE STEERING WHEEL FREE PLAY.

Remedy: REPLACE STEERING CENTERLINK.

ELECTRICAL SYSTEM:WIRING:FRONT UNDERHOOD

WIRING HARNESS IN THE ENGINE COMPARTMENT MAY BE MISROUTED AND SUBJECT TO DAMAGE. CONSEQUENCE OF DEFECT: A SHORT CIRCUIT COULD OCCUR (DURING USE OR WHEN PARKED) WHICH COULD RESULT IN A VEHICLE FIRE.

Remedy: PROPERLY ROUTE WIRING HARNESSES, AS NECESSARY.

POWER TRAIN:AUTOMATIC TRANSMISSION:LEVER AND LINKAGE:COLUMN SHIFT

INCORRECT BOLTS WERE USED IN THE TRANSMISSION LINKAGE ADJUSTMENT MECHANISM. CONSEQUENCE OF DEFECT: THE TRANSMISSION GEAR SHIFT SELECTOR LEVER ON THE STEERING COLUMN WOULD BE ON THE WRONG TRANSMISSION FUNCTION. SHOULD THIS OCCUR, THE DRIVER WOULD FIND THEIR CAR IN A GEAR OTHER THAN THE ONE INDICATED BY SHIFT LEVER INDICATOR. THIS COULD CAUSE AN ACCIDENT IF THE CAR IS LEFT UNATTENDED.

Remedy: REPLACE THE SHIFT LINKAGE TRUNNION, GROMMET AND ADJUSTMENT BOLT.