616 of the
6,577 complaints filed about the GMC Yukon
are about the electrical system —
100% of everything owners reported.
The worst model year for it is 2015.
Water is entering the passenger cabin through failed front sunroof drain tubes on both the left and right sides. The drains discharge inside the A pillars rather than to the exterior, pooling in the driver's side floorboard. An authorized GMC dealer diagnosed the cause in writing on August 12, 2026 as rubber grommet shrinkage and hardened internal buildup preventing water from flowing through, on both the left and right sides simultaneously. The identical bilateral failure mode indicates a component or assembly defect rather than debris blockage. Water is accumulating in the driver's footwell in proximity to cabin electrical components and the fuse block area, creating a risk of electrical shorting, connector corrosion, and circuit failure. Mold has developed in the front carpet and padding on the driver's side, and water intrusion staining is present on the passenger side. The dealer has quoted $2,727.16 to replace the drain tubes and the mold-damaged carpet and padding. The vehicle entered service on February 5, 2025 and has 45,211 miles. GM has issued service bulletin 20-NA-219 addressing sunroof drain hoses on 2021 Yukon, Yukon XL, Tahoe, Suburban, and Escalade models.
NHTSA complaint #11763591 — an unverified report by a vehicle owner.
While driving the vehicle on the interstate, the vehicle shifted to neutral without warning. Our daughter was able to fortunately coast to the side of the interstate without incident. The vehicle was shut off and attempted to turn back on without success, so vehicle was towed to Lugoff Chevy dealership where repairs are always performed. The dealership stated the problem was related to fuse block melted and shorted. The problem was fixed; however, I am not convinced that this shouldn't be something requiring a recall and needs further investigation. There was no warning lamps, messages, or symptoms prior to the failure.
NHTSA complaint #11761018 — an unverified report by a vehicle owner.
I have a 2023 GMC Yukon that has been to the dealership 3 times in a weeks time, and as of today, 8/31/26 will be the fouth time. On 2 occasions, the SUV has entered Limp Mode while driving. I had the SUV towed for the first limp mode, and the dealer claimed it needed recalibration modules. I picked up the car and drove home eight miles, and the check engine light came on. I returned the next day for readings and TCM P0700, P1789, U0101, U220F. The dealer's solution was to recalibrate the gateway module this time. I drove the car about 20-ish miles, and at highway speeds on the freeway, I got limp mode again. Off to the dealership, having the SUV towed again. The dealership has claimed the electrionic car codes clear themselves and because of that they can't re-create the codes to find a solution. I am scared to drive my SUV, I do not feel safe in it let alone my children.
NHTSA complaint #11760969 — an unverified report by a vehicle owner.
Issues with the google voice, transmission issues, engine failure to start or restart. Reported same year vehicle was bought. Repeatedly. Dealership even with video evidence stated could not repeat issue and nothing wrong. My car then starts rattling in the engine and they do a full replacement had it for over three months. Now it’s leaking fluid and smoking. They try to send the consumer away and delay delay until the warranty is over. Unethical practices. They knew there was an issue with my engine as it was on the recall list but kept denying any issues until complete failure. Now less than 20 days after that repair the car is leaking and smoking.
NHTSA complaint #11760762 — an unverified report by a vehicle owner.
This vehicle has been towed into GMC service 3 times to date. #1. 2/2024 (mil 22,662) would not start, low voltage msg, replaced battery. #2. 4/2026 (mil 57,854) vehicle went into N on its own while I was driving down the road, msg on dash "function not available", I stopped and the engine died & would not restart, no engagement from starter motor, found P0615 present, found blown fuse on battery distribution fuse block, replaced. #3. 7/2026 (mil 63,041) vehicle went into N on its own while I was driving down interstate, msg on dash "function not available", I stopped, the engine died and would not restart, found main battery fuse blown, engine seized, found spun rod bearing full of metal debris, replaced engine, radiator, cooler lines, seals, gaskets, bolts, & fluids. My safety was at risk as I was driving down a highway and the interstate 2 of the times the vehicle put itself in N. The problem has been confirmed by the dealer. The vehicle has been inspected by the dealer's service dept. Prior to these incidents I did not notice any symptoms that would have alerted me of what was to come. **This report is referring to my latest incident which was engine seizure. *Two recalls have been performed, #1. 5/2025 "reprogrammed serial data module" & #2. 11/2025 "engine loss of propulsion recall", replaced oil with 0W-40 & "ECM software update recall", replaced ECM with SPS.
NHTSA complaint #11760118 — an unverified report by a vehicle owner.
1. What component or system failed or malfunctioned. The Fuel Pump Module failed unexpectedly while the vehicle was being driven. Failure caused the engine to stall, resulting in a complete loss of power and mobility. Unsure if part is available for inspection. 2021 GMC Yukon have a recall N252516900, but our VIN is not included in this. Can our VIN be added to this recall please? 2. How was your safety or the safety of others put at risk? The vehicle abruptly stalled while being driven through a parking lot, causing a complete loss of power and leaving the vehicle disabled in an active traffic area. Because the vehicle could not be shifted out of PARK, it became an obstruction, creating a hazard for other drivers navigating the parking lot and increasing the risk of a collision. 3. Has the problem been reproduced or confirmed by a dealer or independent service center? Yes. After the vehicle was towed to a local mechanic on a flatbed truck, the dealer diagnosed and confirmed that the Fuel Pump Module had failed, which caused the vehicle to stall and lose power. 4. Has the vehicle or component been inspected by the manufacturer, police, insurance representatives, or others? The vehicle was inspected by a local repair shot, which diagnosed the failed Fuel Pump Module. The vehicle was also evaluated during the towing process. To my knowledge, the manufacturer, police, or insurance representatives have not separately inspected the vehicle or component. 5. Were there any warning lamps, messages, or other symptoms of the problem prior to the failure, and when did they first appear? Prior to the failure, there were no significant symptoms indicating an imminent fuel system failure. When the incident occurred, the vehicle abruptly stalled, lost all power, and displayed a message indicating that the vehicle was "not in a condition to shift," preventing it from being shifted out of PARK. This message first appeared immediately following event.
NHTSA complaint #11759643 — an unverified report by a vehicle owner.
This is a supplemental report to my original complaint (NHTSA ID XXX) regarding my 2024 GMC Yukon (VIN [XXX]). I am providing additional detail: prior to GM's recall being issued, I contacted Hatchett Buick GMC by phone and visited in person on multiple occasions reporting engine sputtering, stalling, hesitation, and total loss of power and electrical shutdown while driving. I was repeatedly told these were minor issues not affecting anyone and not to worry about them. As a result, the vehicle was not formally serviced for these issues until September 2025 — roughly three months after the recall was finally announced, more than a year after I purchased the vehicle. Since that recall repair and a subsequent "best guess" repair performed by GM technicians (their own description, not mine), the vehicle continues to sputter, hesitate, stall, and intermittently lose power. I have ongoing safety concerns driving this vehicle INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
NHTSA complaint #11759361 — an unverified report by a vehicle owner.
On August 22, 2026, I was driving my 2023 GMC Yukon Denali with the 6.2L V8 at highway speed when the vehicle began struggling to maintain power while climbing a hill. The engine then developed a noticeable knocking sound. Shortly afterward, the engine shut off completely while the vehicle was moving, causing a sudden loss of propulsion. I was able to bring the vehicle to a stop, but the engine would not restart. The electronic transmission also would not shift into Neutral and displayed a message indicating that the conditions required to shift were not met. Because the vehicle could not be shifted out of Park, the towing company had difficulty loading and unloading the vehicle. The failure occurred during normal highway driving and created a significant safety concern because the engine shut down without warning while the vehicle was in motion. I am aware of NHTSA Recall 25V-274 / GM Recall N252494000 involving certain GM vehicles equipped with the 6.2L L87 engine, as well as NHTSA Engineering Analysis EA25-007 concerning engine failures and loss of propulsion. At the time of this complaint, the dealership has not yet confirmed the specific mechanical cause of my vehicle’s failure. The vehicle is being taken to an authorized GMC dealership for diagnosis. I am submitting this complaint because of the sudden engine failure and loss of propulsion while traveling on a highway.
NHTSA complaint #11758992 — an unverified report by a vehicle owner.
As I was driving, the vehicle's air conditioning suddenly began blowing warm/hot air. Moments later, the check engine light and all electronic service stability lights illuminated on the dashboard. Simultaneously, the vehicle suffered a complete loss of electronic brake assist, resulting in an extremely hard brake pedal and a severe reduction in braking power. The vehicle also displayed a "No Drive Mode Available" message. Third-party diagnostic scanning revealed network power codes U3018, U3505, P00FF, and P0700, indicating a total loss of power to the Body Control Module (BCM). This is the second life-threatening incident with this vehicle I have experienced following a previous highway engine stall due to engine recall. The vehicle was towed to a GM dealership for diagnostic and emergency electrical repairs.
NHTSA complaint #11757731 — an unverified report by a vehicle owner.
I have a 2023 GMC Yukon AT4. The OnStar/telematics system stopped working. The blue OnStar button does not function and the vehicle no longer communicates with the myGMC app, resulting in loss of connected and OnStar services. A GMC dealership diagnosed a failed OnStar/telematics module and advised that the module must be replaced at a cost of approximately $1,200. I am concerned because this failure affects access to OnStar communication and emergency-related services. I have found reports from other GM owners describing similar telematics/OnStar module failures, and GM has issued service information addressing K73 telematics-module communication faults. I have also opened a case with GMC Customer Assistance. I am reporting this because I believe the repeated failure of a system used for emergency communication warrants investigation.
NHTSA complaint #11756524 — an unverified report by a vehicle owner.
On August 6, 2026, I was driving my family up to Whitefish Mountain Resort (a steep mountain road to a ski resort) for dinner when the ESC warning and "Brake System Failure" warning appeared. I immediately attempted to pull safely to the side of the road. When I pressed the brake pedal, the vehicle did not respond normally. I pushed the brake pedal as far down as I could and had essentially no braking ability. Because we were traveling uphill, the vehicle eventually rolled to a stop. When my brother came with his car he had a vehicle scanning tool. He hooked my vehicle up to it and the tool displayed diagnostic codes P25A2 and P3499. This was an extremely serious safety event. Had we been traveling downhill, approaching an intersection, or driving in heavier traffic, the outcome could have been catastrophic.
NHTSA complaint #11755972 — an unverified report by a vehicle owner.
The contact owns a 2026 GMC Yukon. The contact stated that while walking alongside the rear end of the parked vehicle, the hands free function of the lift gate opened up unintentionally, no warning lights were illuminated. The contact was not injured, however expressed concern for safety as the lift gate will open without user consent while walking along the rear end of the vehicle. The local dealer was contacted however the vehicle was not diagnosed as the contact was advised that the vehicle was manufactured with the feature. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 60.
NHTSA complaint #11755918 — an unverified report by a vehicle owner.
The progressive failure of the factory steering wheel adhesive on my 2025 GMC Yukon creates an immediate, active safety hazard during vehicle operation. The material failure and sticky glue are localized directly around the integrated heating element of the steering wheel. This failure severely impacts driving maneuvers as well as a potential electrical fire hazard. The liquefied glue residue is incredibly sticky and continually transfers to the driver’s hands, resulting in a compromised, slippery grip on the steering wheel. During active driving maneuvers, such as hand-over-hand turning, navigating sharp curves, the loose edges of the peeling leather and separating trim physically catch on the driver's palms. This restricts smooth wheel rotation, disrupts natural hand movement, and threatens a sudden, temporary loss of steering control. This manufacturing defect introduces severe driver distraction and physical interference with critical steering components while driving, compounded by a potential thermal or electrical defect in the steering wheel heating assembly.
NHTSA complaint #11754669 — an unverified report by a vehicle owner.
GM performed a vehicle wide Over the Air reprogramming of the modules incorporated in the VIP/Global B electronics platform in April, 2026. Following that my vehicle became totally dead. Key fob would not unlock the vehicle. Had to use the metal key, open the drivers door. Opened the door, nothing moved. No lights, no movement from anything on the vehicle. Opened the hood, charged the battery and tried to crank it. Would not budge. Starter would not engage. Disconnected the negative battery cable. Tried again. Still would not budge. After an hour of so of trying and using jumper cables from our other vehicle, still would not budge. I disconnected the negative battery cable from the right front fender ground and reattached it. It then cranked. Drove the vehicle 30 miles at interstate speed. 8 miles in city traffic. Drove home and parked it in the garage. Drove it abput 10-12 days later to get breakfast. Parked it, locked it with the key fob. Came back after getting food, key fob would not work. Opened it with the button on the door handle. Got In tried to crank it. Would not budge. Disconnected the negative battery cable twice, before it cranked, but would not drive. Message in dash said vehicle could not be driven. Finally got it cranked. GM never advised that the battery must have a 70% charge at all times for the electronics to work. Owner's manual contains no such statement. Vehicle is defective to the extent that it will leave me stranded in wherever the battery power is less than 70%. Dangerous to get stranded at night on a lonely road or highway, away from cities with tow trucks and competent service personnel. Vehicle in shop 32 days before dealer advised resolution. Modules bricked requiring engine control module and telematics module replacement.
NHTSA complaint #11754040 — an unverified report by a vehicle owner.
The contact owns a 2024 GMC Yukon. The contact stated that there was a strong mildew odor coming from the vehicle while entering the vehicle, and there was moisture around the trunk near the wiring harness. The vehicle was taken to Modern Auto Company (6224 MO-100, Washington, MO 63090), but the cause of the failure was not found. O'Fallon Buick GMC (2150 Technology Dr, O'Fallon, MO 63368) diagnosed the vehicle with a failure of the wiring harness and stated that there was moisture entering the vehicle through the wiring harness. However, after the contact inquired about the odor inside the vehicle, the dealer refused to continue working with the contact. The manufacturer was notified of the failure, and a claim was filed, and an appointment was scheduled for service at Dave Sinclair Buick GMC (5655 S Lindbergh Blvd, St. Louis, MO 63123). The dealer informed the contact that the wiring harness appeared to have already been replaced. The dealer found no leaks inside the vehicle and informed the contact that the vehicle would be returned. The contact hired a mold expert to inspect the vehicle while the vehicle was at the dealer. The mold expert discovered several cases of toxic mold inside the vehicle and deemed the vehicle unsafe to drive. The contact stated that her daughter had severe respiratory issues and was transported in the vehicle. The daughter had several doctor’s visits, was put on several medications, and missed 40 days from school due to her illness. The contact associated the failure with her daughter's illness and stated that her daughter’s health improved once she was no longer transported in the vehicle. Since the failure, the contact had to pay out-of-pocket for a rental vehicle. A field investigator had been hired by the manufacturer to inspect the vehicle, and the contact was awaiting the results. The vehicle remained with the dealer unrepaired. The failure mileage was approximately 27,000.
NHTSA complaint #11751904 — an unverified report by a vehicle owner.
Vehicle is a 2022 GMC Yukon Denali with the 6.2L L87 V8, covered by NHTSA Recall 25V-274 (GM N252494001). The recall remedy was performed. The engine passed the dealer inspection and was given the higher-viscosity 0W-40 oil remedy rather than an engine replacement. On 05/26/2026, at approximately 43,000 miles, the vehicle suffered a sudden engine knock while being driven by my wife. At the same time, the dash displayed Service ESC and Service Traction Control warnings, the vehicle's speed fluctuated on its own without driver input, and the air suspension cycled up and down while the vehicle was in motion. The vehicle had to be towed to the dealer. The dealer diagnosed a failed lifter with resulting camshaft damage and repaired it under the powertrain warranty. The vehicle was out of service approximately fifteen days. Shortly after the vehicle was returned, it began displaying a "Theft Attempted" message on the dash every day. I reported this to the dealer in writing on 06/15/2026 with a photograph at 43,898 miles. The dealer stated it was unlikely to be related and did not scan or diagnose it. On 07/14/2026, approximately 560 miles after the repair, the vehicle became inoperable and had to be towed to the dealer a second time. It is currently at the dealer and has not yet been diagnosed. The unexpected loss of power, speed fluctuation, and stability-control failure at road speed present a serious crash risk. This vehicle passed the 25V-274 inspection remedy and then experienced a valvetrain failure regardless, which is directly relevant to Recall Query RQ26001 into the adequacy of that remedy.
NHTSA complaint #11750311 — an unverified report by a vehicle owner.
Odometer Fraud. The contact purchased a 2013 GMC Yukon. It was discovered that there was a mileage discrepancy. The vehicle was an independent dealer sale. At the time of purchase, the vehicle mileage was 92,000; however, a diagnostic report at O'Reilly's listed mileage as 172,000.
NHTSA complaint #11749296 — an unverified report by a vehicle owner.
On June 25, 2026 my 2023 GMC Yukon Denali with 53,456 miles was brought to an authorized GMC dealership after displaying a Service 4WD warning light and exhibiting a groaning noise when shifting into Drive and Reverse. The vehicle was diagnosed with the following brake system fault codes: P25A2, C0511, C0517, C1595 and C1596. These codes indicate brake control module failure and wheel speed sensor faults which are safety critical components. The dealership confirmed these findings but stated the repairs are not covered under the GMC powertrain warranty. Given that these are safety critical brake system failures on a nearly new vehicle with only 53,456 miles, we contacted GMC Customer Care on July 1, 2026 to request coverage under goodwill warranty as we believe these failures constitute a manufacturing defect. A case was opened however after 7 days no case advisor has been assigned and no decision has been made despite two promised timelines not being met. The brake system failures on a nearly new vehicle represent a serious safety concern as these systems directly affect the vehicle's ability to stop safely. The vehicle has been at the dealership since June 25, 2026 and remains unrepaired.
NHTSA complaint #11749116 — an unverified report by a vehicle owner.
Issue with the trailer brake system keeps coming up on my dash. I know a lot of other people have had the same issue keeps dinging will not stop causes me to get distracted while driving. Unable to use other features because of this distraction and safety issue. The safety issue needs to be fixed this is an effective product with so many people having an issue you need to do a recall. I did let Graff Chevrolet in Mount Pleasant Michigan no and I took a picture and showed them.
NHTSA complaint #11748158 — an unverified report by a vehicle owner.
The contact owns a 2023 GMC Yukon. While the contact's wife was driving approximately 5-10 MPH on a city street and approaching a stop sign, the vehicle experienced a failure and became inoperable. The contact stated that while the driver was attempting to restart the vehicle, the battery warning light and engine warning light illuminated, and the "Low Battery - Start Engine" message was displayed. The vehicle was towed directly to a dealer to be diagnosed. The dealer was unable to determine the cause of the failure but provided an estimate for the valve springs inspection. The vehicle was not repaired. The manufacturer was notified of the failure and was working with the dealer to determine how to repair the vehicle. The failure mileage was approximately 71,481.
NHTSA complaint #11747346 — an unverified report by a vehicle owner.