Owners have filed 1,083 complaints
about the 2019 Jeep Wrangler with NHTSA between 2018 and 2026.
The largest single group is the steering.
Across this model's run it ranks 5 of 33 worst.
The letter says how bad. This says what kind — whether this year drew
an unusual number of complaints, unusually dangerous
ones, or failures that arrived unusually early.
The dashed ring is 50 — the national norm. Further out is worse.
Complaint volume — 80
Against the median year of the Jeep Wrangler. 50 means typical for this
model; 100 means roughly double.
Severity — 20
4% of these complaints
involved a crash, fire, injury or death, against a national rate of
9.7%.
Early failure — 100
89% of failures with a mileage on record happened under
36,000 miles, against a national rate of
29%.
NHTSA files every complaint against a named sub-assembly, not just a
system. This is the difference between knowing it was "the engine" and
knowing which part of it — the list to hand a mechanic.
Body
2152.5%
Instrument Cluster/Panel
1127.5%
Automatic Emergency Braking
25.0%
Warnings
25.0%
Hand Heater/Cooler
12.5%
Software
12.5%
SUN Visor
12.5%
Adaptive Cruise Control
12.5%
When it fails
Odometer readings owners gave when they filed. About half of all
complaints include one.
Under 1,000 miles
15428.6%
1,000 – 9,999 miles
16831.2%
10,000 – 24,999 miles
13224.5%
25,000 – 49,999 miles
397.2%
50,000 – 74,999 miles
203.7%
75,000 – 99,999 miles
122.2%
100,000 – 149,999 miles
142.6%
When owners complained
A spike years after the car went on sale usually means a part wearing
out on schedule across the whole fleet — the kind of pattern no single
owner can see from inside their own car.
Dec 2018peak 50Aug 2026
NHTSA investigations into the 2019 Jeep Wrangler
An investigation is the step before a recall: the agency has seen enough
complaints to look into a pattern itself. An open one means it thinks
something may be wrong and nothing has been fixed yet.
PE19012Opened 16 Sep 2019Closed 29 Oct 2023STEERING
Frame weld deficiencies
On September 16, 2019, the Office of Defects Investigation (ODI) granted Defect Petition DP18-004 and opened Preliminary Evaluation PE19-012 to investigate allegations of deficient frame welds and their potential safety related effects on 2018-2019 Jeep Wranglers. Due to a previous steering related recall that was caused by a misaligned weld on the front track bar (NHTSA Recall No. 18V-675), ODI decided to include reports of steering shimmy or wobble, loose steering, and steering stiction (loss of power steering) as part of this investigation and parent petition (DP18-004). ODI received inform...
DP18004Opened 16 Nov 2018Closed 17 Sep 2019STEERING
Frame Weld Deficiencies
In a letter received on October 24, 2018, a citizen petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a safety defect investigation into frame weld deficiencies on model year (MY) 2018 'JL' Jeep Wrangler vehicles. The petitioner described a broad list of frame weld deficiencies, including porous welds, excessive slag, lack of weld penetration, over penetration of welds, overweld or weld drip, and weld splash. The weld defects are allegedly located at a variety of locations on the frame assembly.On November 16, 2018, the Office of Defects Investigation (ODI) open...
Recalls on the 2019 Jeep Wrangler
A complaint is one owner's allegation. A recall is the point at which
the manufacturer or a regulator agreed the defect is real and dangerous
enough to fix for free — however old the car is.
United States — NHTSA
24V676000
BACK OVER PREVENTION: SENSING SYSTEM: CAMERA
Chrysler (FCA US, LLC) is recalling certain 2018-2024 Jeep Wrangler vehicles. The wiring harness for the rearview camera and the center brake light may short circuit, which can disable the rearview camera image and center brake light. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 111, "Rear Visibility" and 108, "Lamps, Reflective Devices, and Associated Equipment."
Risk: A rearview camera image that does not display decreases the driver's visibility, increasing the risk of a crash. Additionally, a center brake light that fails to illuminate can fail to indicate to other drivers that the vehicle is slowing down, increasing the risk of a crash.
24V652000
ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL
Chrysler (FCA US, LLC) is recalling certain 2020-2024 Jeep Gladiator and 2018-2024 Jeep Wrangler vehicles. The instrument panel cluster may experience an internal short circuit and fail. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 101, "Controls and Displays."
Risk: An instrument panel that fails to display critical safety information, such as the speedometer or warning lights, can increase the risk of a crash.
23V116000
POWER TRAIN:CLUTCH ASSEMBLY
Chrysler (FCA US, LLC) is recalling certain 2018-2023 Jeep Wrangler, and 2020-2023 Jeep Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.
Risk: Overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.
21V028000
POWER TRAIN:CLUTCH ASSEMBLY
Chrysler (FCA US, LLC) is recalling certain 2018-2021 Jeep Wrangler and 2020-2021 Jeep Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.
Risk: Overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.
20V580000
SEAT BELTS
Chrysler (FCA US LLC) is recalling certain 2019 Jeep Wrangler and Ram 2500, 2019-2020 Ram 1500 and 2020 Jeep Gladiator vehicles. In the event of a crash, a front seat belt retractor may not properly slow the occupant's forward movement after locking.
Risk: In the event of a crash, if the front seat belts fail to lock, there is an increased risk of injury.
20V191000
BACK OVER PREVENTION: SENSING SYSTEM: CAMERA
Chrysler (FCA US LLC) is recalling certain 2020 Jeep Gladiator and Jeep Cherokee, 2019-2020 Ram 1500 Pickup, Ram 2500 Pickup, Ram 3500 Pickup, Chrysler Pacifica, Dodge Durango, Jeep Grand Cherokee, Jeep Wrangler, and Jeep Renegade and 2019 Dodge Challenger vehicles equipped with 8.4" or 12" radio displays. A software error can cause the rearview camera image to remain displayed after the vehicle has been shifted out of reverse. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 111, "Rearview Mirrors."
Risk: The lingering rearview image can distract the driver, increasing the risk of a crash.
20V124000
POWER TRAIN:CLUTCH ASSEMBLY
Chrysler (FCA US LLC) is recalling certain 2018-2020 Jeep Wrangler and 2020 Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.
Risk: The overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.
19V201000
STEERING
Chrysler (FCA US LLC) is recalling certain 2019 Jeep Wrangler and 2019 Ram 1500 vehicles. These vehicles have improperly machined steering column stub shafts that may break, possibly causing the steering wheel to detach from the steering column.
Risk: If the steering wheel detaches from the steering column, the driver may lose control of the vehicle, increasing the risk of crash.
Canada — Transport Canada
Canada runs its own recall programme, and its campaigns do not
always mirror the American ones.
Recall 20245041,613 units in Canada
Lights And Instruments
Issue: On certain vehicles, the instrument panel cluster could stop working. As a result, warnings, tell-tales and gauges may not display. Note: This recall only affects vehicles equipped with a 3.5" instrument cluster panel. Safety Risk: Warnings, tell-tales and gauges that don't display could increase the risk of a crash. Corrective Actions: FCA Canada will notify owners by mail and advise you to take your vehicle to a dealership to replace the instrument panel cluster.
Recall 20230897,464 units in Canada
Powertrain
Issue: Under certain conditions, the clutch pressure plate could overheat and break. If this happens, the pressure plate may also crack or break the transmission case. This could cause debris to fall from the vehicle. Note: This recall only affects certain vehicles equipped with a 3.6 L engine and a manual transmission. Vehicles repaired under FCA Canada recalls Y01, Y03 and Y07 (Transport Canada recall 2021-035) also require this repair. Safety Risk: Debris from an overheated and fractured pressure plate could contact nearby parts and increase the risk of a fire. Parts that fall from the vehicle could create a road hazard for others and increase the risk of injury. Corrective Actions: FCA Canada will notify owners by mail and advise you to tale your vehicle to a dealership to replace the clutch assembly. The dealer will also inspect and, if necessary, update the instrument panel cluster and powertrain control module software.
Recall 20210354,349 units in Canada
Powertrain
Issue: In certain circumstances, the clutch pressure plate could overheat and break. If this happens, the pressure plate may also crack or break the transmission case. This could cause debris to fall from the vehicle. Note: This recall only affects certain vehicles equipped with a 3.6 L engine and a manual transmission. Safety Risk: Debris from an overheated and fractured pressure plate could contact nearby parts and increase the risk of a fire. Parts that fall from the vehicle could create a road hazard for others, and increase the risk of injury. Corrective Actions: FCA Canada will notify owners by mail and instruct you to take your vehicle to a dealer to update vehicle software. This update will reduce the engine power if the clutch overheats.
Recall 2020456127 units in Canada
Seats And Restraints
Issue: On certain vehicles, there could be a problem with the front seat belt retractors. As a result, the seat belts may not work as designed in a crash. Safety Risk: A seat belt that does not work properly could increase the risk of injury in a crash. Corrective Actions: Fiat Chrysler Automobiles will notify owners by mail and instruct you to take your vehicle to a dealer to replace the front seat belts.
Recall 202014546,772 units in Canada
Visual System
Issue: On certain vehicles, the rearview camera image may be displayed even after the transmission is shifted out of reverse. This could cause a possible distraction for the driver. Canadian regulations require the rearview image to turn off within 10 seconds after shifting from reverse gear. Safety Risk: A driver that is distracted could have an increased risk of a crash. Corrective Actions: FCA Canada will notify owners by mail and instruct you to take your vehicle to a dealer to update the radio software.
Recall 20200833,513 units in Canada
Powertrain
Issue: On certain vehicles equipped with a manual transmission, the clutch pressure plate could overheat and break. If this happens, there would be a loss of power to the wheels. A broken pressure plate may also crack or break the transmission case. This could cause debris to fall from the vehicle. Safety Risk: A sudden of loss power to the wheels could increase the risk of a crash. Additionally, debris from an overheated and fractured pressure plate could contact nearby parts and increase the risk of a fire. Parts that fall from the vehicle could create a road hazard for others, and increase the risk of injury. Corrective Actions: FCA Canada will notify owners by mail and instruct you to take your vehicle to a dealer to inspect the clutch system, install a protective hose sleeve, reroute a wire harness, and replace components as necessary
Recall 20191389 units in Canada
Steering
Issue: On certain vehicles, the steering shaft may not have been properly manufactured. This could cause it to separate and cause a loss of steering control. Safety Risk: A loss of steering control could create the risk of a crash. Corrective Actions: The company will notify owners by mail. Owners will be instructed to take their vehicle to a dealer to inspect, and if necessary, replace the steering column assembly.
Reports where the owner recorded a crash, a fire, an injury or a death.
Chandler, AZFire
POWER TRAIN
VEHICLE & INCIDENT: 2019 Jeep Wrangler JL 2.0L Turbo. While climbing an extended grade on Hwy 87, vehicle experienced a sudden sluggish throttle anomaly and rapid coolant temperature spike from ~215F to 255F under load. Vehicle was pulled off and shut down within ~20 seconds. SUSPECTED FAILURE MODE & UNDERHOOD FIRE: Upon opening the hood, pressurized coolant had sprayed across the engine bay from a split in the smaller rubber hose branch of the engine coolant outlet assembly (Mopar PN 68280797AC). The hose split longitudinally ~13mm with the center ~32mm from the hose end. The vehicle is equipped with a Baja Designs T-Fitting to replace 68280784A The hot, pressurized coolant sprayed directly onto the exposed, center section of the turbocharger between the compressor and turbine sections and on the turbine section itself. The coolant is suspected to have flash-ignited on contact with the turbo, creating an active under hood fire that began spreading to the hood insulation liner. The fire was successfully doused roadside with water, preventing a total vehicle burn-down. No other fuel sources were noted and the lines to the turbocharger were intact and did not show evidence of a leak. SAFETY CONCERN / HAZARD FOR NHTSA: 1. FIRE HAZARD: Pressurized factory coolant hoses and plastic junctions on the 2.0T GMET4 are routed in close proximity to the unshielded turbine housing. A hose rupture under normal grade-climbing thermal loads results in high-pressure atomized coolant hitting an ignition source well above its auto-ignition point. 2. COMPONENT DEGRADATION: Rubber lines near the engine outlet appear susceptible to heat-fatigue failure under high ambient/high load conditions, posing a sudden fire hazard at highway speeds. REPAIR: Roadside trim/re-clamp of the split hose allowed temporary transit. Replacing full hose assembly (68280797AC), upgrading radiator lines, and performing a full OAT coolant flush/vacuum refill. No oil contamination was noted after the incident.
NHTSA complaint #11755697 — an unverified report by a vehicle owner.
Chandler, AZFire
ENGINE
VEHICLE & INCIDENT: 2019 Jeep Wrangler JL 2.0L Turbo. While climbing an extended grade on Hwy 87, vehicle experienced a sudden sluggish throttle anomaly and rapid coolant temperature spike from ~215F to 255F under load. Vehicle was pulled off and shut down within ~20 seconds. SUSPECTED FAILURE MODE & UNDERHOOD FIRE: Upon opening the hood, pressurized coolant had sprayed across the engine bay from a split in the smaller rubber hose branch of the engine coolant outlet assembly (Mopar PN 68280797AC). The hose split longitudinally ~13mm with the center ~32mm from the hose end. The vehicle is equipped with a Baja Designs T-Fitting to replace 68280784A The hot, pressurized coolant sprayed directly onto the exposed, center section of the turbocharger between the compressor and turbine sections and on the turbine section itself. The coolant is suspected to have flash-ignited on contact with the turbo, creating an active under hood fire that began spreading to the hood insulation liner. The fire was successfully doused roadside with water, preventing a total vehicle burn-down. No other fuel sources were noted and the lines to the turbocharger were intact and did not show evidence of a leak. SAFETY CONCERN / HAZARD FOR NHTSA: 1. FIRE HAZARD: Pressurized factory coolant hoses and plastic junctions on the 2.0T GMET4 are routed in close proximity to the unshielded turbine housing. A hose rupture under normal grade-climbing thermal loads results in high-pressure atomized coolant hitting an ignition source well above its auto-ignition point. 2. COMPONENT DEGRADATION: Rubber lines near the engine outlet appear susceptible to heat-fatigue failure under high ambient/high load conditions, posing a sudden fire hazard at highway speeds. REPAIR: Roadside trim/re-clamp of the split hose allowed temporary transit. Replacing full hose assembly (68280797AC), upgrading radiator lines, and performing a full OAT coolant flush/vacuum refill. No oil contamination was noted after the incident.
NHTSA complaint #11755697 — an unverified report by a vehicle owner.
at 65,000 milesDunnellon, FLFire
ENGINE
The contact owns a 2019 Jeep Wrangler. The contact stated that while driving at an undisclosed speed, the Check Engine warning light illuminated. The vehicle was taken to O'Reily's, where a portable diagnostic machine was used; however, no fault codes were retrieved. The contact stated that the check engine warning light was an old warning light. In addition, the contact was informed that the vehicle could be driven. The contact stated that while driving to the residence, the check engine warning light turned off. The failure reoccurred, and the engine seized. The contact stated that the vehicle rolled near the shoulder of the road. The contact became aware of smoke coming from the engine compartment. The contact stated that a good Samaritan stopped and assisted the contact. The contact and a good Samaritan became aware of fire coming from the engine compartment near the battery. The good Samaritan attempted to extinguish the fire with a sweatshirt, then used a jug of water from inside the vehicle. No injuries were sustained. The vehicle was towed to the local tow yard. The Carvana dealer where the vehicle was purchased was made aware of the failure. The vehicle was then towed to a repair shop assigned by Carvana. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 65,000.
NHTSA complaint #11744871 — an unverified report by a vehicle owner.
Gulfport, MSFire
ELECTRICAL SYSTEM
I was driving my 2019 Jeep Wrangler Unlimited Sahara 2.0T/AT to the gym with my spouse. No Check Engine Light, Jeep Temps were perfect. All gauges operated as it should, so there was no sign of trouble. The vehicle was OFF. We parked and walked into the gym and then into the 1 set of exercises, Someone yelled in the gym that someone's truck was on fire. We ran outside and Lo and Behold it was our Jeep. The Engine Compartment Was totally Destroyed. Please Look At the Pictures for Reference.
NHTSA complaint #11732154 — an unverified report by a vehicle owner.
Gulfport, MSFire
ENGINE
I was driving my 2019 Jeep Wrangler Unlimited Sahara 2.0T/AT to the gym with my spouse. No Check Engine Light, Jeep Temps were perfect. All gauges operated as it should, so there was no sign of trouble. The vehicle was OFF. We parked and walked into the gym and then into the 1 set of exercises, Someone yelled in the gym that someone's truck was on fire. We ran outside and Lo and Behold it was our Jeep. The Engine Compartment Was totally Destroyed. Please Look At the Pictures for Reference.
NHTSA complaint #11732154 — an unverified report by a vehicle owner.
Mansfield, TXFire
POWER TRAIN
Driving on interstate 35 south in fifth gear. There was a loud BANG! and then we lost power. Barely made it off a tight overpass and we saw the smoke. The car was quickly on fires we got out as it started to engulf the jeep with flames. It was a total and complete loss - and very dangerous.
NHTSA complaint #11645832 — an unverified report by a vehicle owner.
The most recent complaints
In the owners' own words, exactly as filed with NHTSA.
Alcoa, TN
STEERING
Check engine, ABS, Service Shifter suddenly pops up and the steering was hard to turn almost had an accident
NHTSA complaint #11757827 — an unverified report by a vehicle owner.
West Chester, PA
UNKNOWN OR OTHER
The IPC Cluster stopped working and the screen is completely blank. It is unsafe to drive since I don’t know how fast I’m going, how much gas is in the tank, and inability to see any warning lights. The recall for this is Recall Campaign 30B/NHTSA 24-V 652 for jeeps with the 3.5 inch cluster layout, which I have but my VIN is not listed on the recall list. It should be!
NHTSA complaint #11757749 — an unverified report by a vehicle owner.
Alcoa, TN
ELECTRICAL SYSTEM
Check engine, ABS, Service Shifter suddenly pops up and the steering was hard to turn almost had an accident
NHTSA complaint #11757827 — an unverified report by a vehicle owner.
Alcoa, TN
SERVICE BRAKES
Check engine, ABS, Service Shifter suddenly pops up and the steering was hard to turn almost had an accident
NHTSA complaint #11757827 — an unverified report by a vehicle owner.
Duxbury, MA
ELECTRICAL SYSTEM
The contact owns a 2019 Jeep Wrangler. The contact stated that while driving at an undisclosed speed, the instrument panel was blank. The vehicle was taken to the dealer and was diagnosed with instrument cluster failure. The contact was informed that the instrument cluster needed to be replaced. The vehicle was awaiting the repair. The manufacturer was notified of the failure and referenced NHTSA Campaign Number: 24V652000 (Electrical System); however, the VIN was not included in the recall. The failure mileage was unknown.
NHTSA complaint #11757421 — an unverified report by a vehicle owner.
Snohomish, WA
ELECTRICAL SYSTEM
The 3.5-inch Instrument Panel Cluster went completely black while operating the vehicle, causing a total loss of speedometer and critical safety indicators (violating FMVSS 101). Concurrently, the engine computer limited vehicle performance to 3,000 RPM (limp mode). The vehicle exhibits the exact failure mode detailed in NHTSA Campaign 24V-652 (Jeep Recall 30B), but the manufacturer has not yet added this VIN to the recall population.
NHTSA complaint #11756483 — an unverified report by a vehicle owner.
Wesley Chapel, FL
SERVICE BRAKES
ABS pump and module combination is making brake calipers to not released. It’s been two times in 6 months my brakes are used up and calipers locked. Jeep knows this issue across its brand of vehicles but not called for a recall. Parts are also in back order that says lot of vehicles has issues. Confirmed with local dealership.
NHTSA complaint #11756488 — an unverified report by a vehicle owner.
Chandler, AZFire
POWER TRAIN
VEHICLE & INCIDENT: 2019 Jeep Wrangler JL 2.0L Turbo. While climbing an extended grade on Hwy 87, vehicle experienced a sudden sluggish throttle anomaly and rapid coolant temperature spike from ~215F to 255F under load. Vehicle was pulled off and shut down within ~20 seconds. SUSPECTED FAILURE MODE & UNDERHOOD FIRE: Upon opening the hood, pressurized coolant had sprayed across the engine bay from a split in the smaller rubber hose branch of the engine coolant outlet assembly (Mopar PN 68280797AC). The hose split longitudinally ~13mm with the center ~32mm from the hose end. The vehicle is equipped with a Baja Designs T-Fitting to replace 68280784A The hot, pressurized coolant sprayed directly onto the exposed, center section of the turbocharger between the compressor and turbine sections and on the turbine section itself. The coolant is suspected to have flash-ignited on contact with the turbo, creating an active under hood fire that began spreading to the hood insulation liner. The fire was successfully doused roadside with water, preventing a total vehicle burn-down. No other fuel sources were noted and the lines to the turbocharger were intact and did not show evidence of a leak. SAFETY CONCERN / HAZARD FOR NHTSA: 1. FIRE HAZARD: Pressurized factory coolant hoses and plastic junctions on the 2.0T GMET4 are routed in close proximity to the unshielded turbine housing. A hose rupture under normal grade-climbing thermal loads results in high-pressure atomized coolant hitting an ignition source well above its auto-ignition point. 2. COMPONENT DEGRADATION: Rubber lines near the engine outlet appear susceptible to heat-fatigue failure under high ambient/high load conditions, posing a sudden fire hazard at highway speeds. REPAIR: Roadside trim/re-clamp of the split hose allowed temporary transit. Replacing full hose assembly (68280797AC), upgrading radiator lines, and performing a full OAT coolant flush/vacuum refill. No oil contamination was noted after the incident.
NHTSA complaint #11755697 — an unverified report by a vehicle owner.
Chandler, AZFire
ENGINE
VEHICLE & INCIDENT: 2019 Jeep Wrangler JL 2.0L Turbo. While climbing an extended grade on Hwy 87, vehicle experienced a sudden sluggish throttle anomaly and rapid coolant temperature spike from ~215F to 255F under load. Vehicle was pulled off and shut down within ~20 seconds. SUSPECTED FAILURE MODE & UNDERHOOD FIRE: Upon opening the hood, pressurized coolant had sprayed across the engine bay from a split in the smaller rubber hose branch of the engine coolant outlet assembly (Mopar PN 68280797AC). The hose split longitudinally ~13mm with the center ~32mm from the hose end. The vehicle is equipped with a Baja Designs T-Fitting to replace 68280784A The hot, pressurized coolant sprayed directly onto the exposed, center section of the turbocharger between the compressor and turbine sections and on the turbine section itself. The coolant is suspected to have flash-ignited on contact with the turbo, creating an active under hood fire that began spreading to the hood insulation liner. The fire was successfully doused roadside with water, preventing a total vehicle burn-down. No other fuel sources were noted and the lines to the turbocharger were intact and did not show evidence of a leak. SAFETY CONCERN / HAZARD FOR NHTSA: 1. FIRE HAZARD: Pressurized factory coolant hoses and plastic junctions on the 2.0T GMET4 are routed in close proximity to the unshielded turbine housing. A hose rupture under normal grade-climbing thermal loads results in high-pressure atomized coolant hitting an ignition source well above its auto-ignition point. 2. COMPONENT DEGRADATION: Rubber lines near the engine outlet appear susceptible to heat-fatigue failure under high ambient/high load conditions, posing a sudden fire hazard at highway speeds. REPAIR: Roadside trim/re-clamp of the split hose allowed temporary transit. Replacing full hose assembly (68280797AC), upgrading radiator lines, and performing a full OAT coolant flush/vacuum refill. No oil contamination was noted after the incident.
NHTSA complaint #11755697 — an unverified report by a vehicle owner.
Newcomerstown, OH
STRUCTURE:BODY
The vehicle is experiencing severe, premature galvanic corrosion on the doors, hinges, and hood due to a documented factory defect where aluminum panels press directly against steel hinges without proper isolation (acknowledged by the manufacturer in TSB 31-001-24).This is a critical structural and safety hazard covered under Federal Motor Vehicle Safety Standard (FMVSS) 206, which regulates door locks and door retention components. The advanced sub-surface corrosion is causing the metal surrounding the door hinges to degrade and oxidize, causing the paint to blister, bubble, and flake off. Over time, this structural failure poses an imminent safety risk of causing the door hinges to seize or bind, potentially jamming the doors shut during an emergency and trapping occupants inside the vehicle. Furthermore, the degradation of these hinge components creates a severe risk of the doors failing and opening unexpectedly while the vehicle is in motion at highway speeds.The manufacturer is refusing to address this structural defect because the vehicle passed its 5-year calendar warranty window, ignoring the fact that this sub-surface chemical reaction takes years to visibly manifest. This defect requires a formal safety investigation and an expanded recall to protect drivers from door-retention failures.
NHTSA complaint #11753493 — an unverified report by a vehicle owner.
at 71,663 milesWeston, CT
STEERING
The contact owns a 2019 Jeep Wrangler. While the contact's daughter was driving at an undisclosed speed, the heated steering wheel feature was enabled; however, the heated steering wheel feature failed to function as intended. In addition, the contact became aware of a burning odor. The contact deactivated the heated steering wheel feature. The vehicle was taken to the dealer, where it was diagnosed with interior melting of the steering wheel. The contact was informed that the steering wheel and the steering wheel housing needed to be replaced. The vehicle was not repaired. The contact was informed that the parts were ordered. The contact referenced an unknown recall; however, the VIN was not associated with a recall related to the failure. The manufacturer was made aware of the failure but provided no assistance. The contact was advised to contact the NHTSA Hotline and report the failure. The failure mileage was approximately 71,663.
NHTSA complaint #11752022 — an unverified report by a vehicle owner.
at 68,482 milesCovington, WA
SERVICE BRAKES, HYDRAULIC
The contact owns a 2019 Jeep Wrangler. The contact stated that while driving approximately 60 MPH, the vehicle suddenly lost motive power and stalled, and the vehicle went into LIMP Mode. The check engine warning light was illuminated. The driver was able to safely move the vehicle to the side of the road. The vehicle was taken to an independent mechanic to be diagnosed, and the contact was informed that the ABS module had failed. The local dealer was contacted and advised that the replacement part was on backorder and referred the contact to the manufacturer for assistance. The vehicle was not diagnosed or repaired. The manufacturer was contacted and confirmed that the replacement part was not available. The failure mileage was approximately 68,482.
NHTSA complaint #11752102 — an unverified report by a vehicle owner.
at 68,482 milesCovington, WA
ENGINE
The contact owns a 2019 Jeep Wrangler. The contact stated that while driving approximately 60 MPH, the vehicle suddenly lost motive power and stalled, and the vehicle went into LIMP Mode. The check engine warning light was illuminated. The driver was able to safely move the vehicle to the side of the road. The vehicle was taken to an independent mechanic to be diagnosed, and the contact was informed that the ABS module had failed. The local dealer was contacted and advised that the replacement part was on backorder and referred the contact to the manufacturer for assistance. The vehicle was not diagnosed or repaired. The manufacturer was contacted and confirmed that the replacement part was not available. The failure mileage was approximately 68,482.
NHTSA complaint #11752102 — an unverified report by a vehicle owner.
Glendale, CA
ELECTRICAL SYSTEM
Instrument panel cluster has malfunctioned. Spedometer, tachometer, odometer, fuel guage, oil temperature, tire pressuer, and several other dashboard displays both analog and digital are not functional. The instruments on the dashboard have gone blank and do not provide a reading when the car is powered on. As a consequence of the instrument panel cluster failure, I am unable to see my exact speed, potential vehicle warning indications, and fuel levels while operating the vehicle putting the safety of myself and others at risk. The vehichle has a history of dealership and mechanic inspections. No warning lamps, messages, or other symptoms were evident prior to the failure of the instrument panel cluster.
NHTSA complaint #11751158 — an unverified report by a vehicle owner.
Newark, DE
SERVICE BRAKES
The front left (drivers side) caliper stuck and the the brake line needs replaced. The caliper sticking was causing extreme heat that could have caused a fire as well as brake failure. The repair shop confirmed that the parts need replaced. No warning messages were ever appear. Additionally, the left brake line from Mopar is not available and there are almost a 1000 on back order. The Jeep is not drivable and no parts available for the foreseeable future to fix the problem.
NHTSA complaint #11751023 — an unverified report by a vehicle owner.
Allenhurst, GA
ELECTRICAL SYSTEM
Instrument panel cluster failing making it difficult to determine mph, fuel in vehicle, mileage, etc. panel was flashing and blacking out while driving creating a distraction, photos could not be obtained during worst of incident because actively driving.
NHTSA complaint #11748733 — an unverified report by a vehicle owner.
Allenhurst, GA
ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL
Instrument panel cluster failing making it difficult to determine mph, fuel in vehicle, mileage, etc. panel was flashing and blacking out while driving creating a distraction, photos could not be obtained during worst of incident because actively driving.
NHTSA complaint #11748733 — an unverified report by a vehicle owner.
Bealeton, VA
POWER TRAIN:CLUTCH ASSEMBLY
There was a recall done on the clutch system back in 2023 and now the same problem has occurred, and I have to replace my entire clutch system.
NHTSA complaint #11748121 — an unverified report by a vehicle owner.
Blythewood, SC
ELECTRICAL SYSTEM
Instrument panel cluster failure in my 2019 jeep wrangler unlimted sport. instrument panel cluster +9 Stellantis (Jeep) recalled certain 2019 Jeep Wranglers (Campaign 24V-652 or Recall #30B) because their 3.5-inch instrument panel clusters can short-circuit and go completely dark. This causes you to lose your speedometer and critical warning lights, increasing crash risks. Dealers replacement . Thing is none of all 4 are honoring this recall. Im having the same issues as this recall. FCA, NHTSA, CHRYSLER/JEEP, STELLANTIS. ALL 4 i have called even made a complaint and all i get is so rry cant help you cause my vin number is not on the recall yet having the same recall issues. And i have to drive back to [XXX] tomorrow from [XXX] i pray that i dont get into any accident INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
NHTSA complaint #11748089 — an unverified report by a vehicle owner.
at 82,000 milesBrandon, MN
STEERING
The contact owns a 2019 Jeep Wrangler. The contact stated that while driving at an undisclosed speed, the vehicle stalled. The contact pulled over and waited for several minutes before restarting the vehicle. The vehicle was taken to the dealer, who replaced the wiring harness, but the failure persisted with the speedometer and fuel gauge fluctuating and the instrument panel icons flashing. Additionally, the vehicle was jerking and experienced a loss of power steering assist while driving. The vehicle was jumpstarted. The vehicle was taken back to the dealer; however, the vehicle was not yet diagnosed or repaired. The contact related the failure to NHTSA Campaign Number: 24V652000 (Electrical System); however, the VIN was not included in the recall. The manufacturer was not made aware of the failure. The failure mileage was approximately 82,000.
NHTSA complaint #11746391 — an unverified report by a vehicle owner.
at 82,000 milesBrandon, MN
ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL
The contact owns a 2019 Jeep Wrangler. The contact stated that while driving at an undisclosed speed, the vehicle stalled. The contact pulled over and waited for several minutes before restarting the vehicle. The vehicle was taken to the dealer, who replaced the wiring harness, but the failure persisted with the speedometer and fuel gauge fluctuating and the instrument panel icons flashing. Additionally, the vehicle was jerking and experienced a loss of power steering assist while driving. The vehicle was jumpstarted. The vehicle was taken back to the dealer; however, the vehicle was not yet diagnosed or repaired. The contact related the failure to NHTSA Campaign Number: 24V652000 (Electrical System); however, the VIN was not included in the recall. The manufacturer was not made aware of the failure. The failure mileage was approximately 82,000.
NHTSA complaint #11746391 — an unverified report by a vehicle owner.
at 50,000 milesSaraosta, FL
ELECTRICAL SYSTEM:HORN
The contact owns a 2019 Jeep Wrangler. The contact stated that the horn was inoperable. The contact attempted to depress the horn on several occasions, but the horn failed to operate. The contact's husband attempted to depress the horn, and the horn failed to operate. There were no warning lights illuminated. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not contacted. The failure mileage was approximately 50,000.
NHTSA complaint #11745666 — an unverified report by a vehicle owner.
at 65,000 milesDunnellon, FLFire
ENGINE
The contact owns a 2019 Jeep Wrangler. The contact stated that while driving at an undisclosed speed, the Check Engine warning light illuminated. The vehicle was taken to O'Reily's, where a portable diagnostic machine was used; however, no fault codes were retrieved. The contact stated that the check engine warning light was an old warning light. In addition, the contact was informed that the vehicle could be driven. The contact stated that while driving to the residence, the check engine warning light turned off. The failure reoccurred, and the engine seized. The contact stated that the vehicle rolled near the shoulder of the road. The contact became aware of smoke coming from the engine compartment. The contact stated that a good Samaritan stopped and assisted the contact. The contact and a good Samaritan became aware of fire coming from the engine compartment near the battery. The good Samaritan attempted to extinguish the fire with a sweatshirt, then used a jug of water from inside the vehicle. No injuries were sustained. The vehicle was towed to the local tow yard. The Carvana dealer where the vehicle was purchased was made aware of the failure. The vehicle was then towed to a repair shop assigned by Carvana. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 65,000.
NHTSA complaint #11744871 — an unverified report by a vehicle owner.
Boxford, MA
POWER TRAIN
The 48V eTorque Power Pack Unit (PPU), BPCM, and associated cables failed on my 2019 Jeep Wrangler, causing the vehicle to stall and lose all acceleration while driving on the highway. All components are available for inspection upon request. In June 2025, a non-Jeep service center identified stored diagnostic code P0A9C-00 (48V hybrid battery temperature sensor circuit performance failure) along with multiple low voltage codes in the power steering system. The technician noted the issue needed to be addressed by an authorized Jeep dealer, as there was insufficient information to perform a repair on the 48V hybrid system. In September 2025, while driving on the highway, the engine stalled and the vehicle completely lost acceleration and would not restart. The vehicle required towing to an authorized Jeep dealer. A sudden and unexpected loss of acceleration and engine stall on a highway creates an extreme risk of rear-end collision and potential serious injury or fatality to the driver and other motorists. The problem was confirmed by an authorized FCA/Jeep dealer who found the same diagnostic code P0A9C-00, along with corrosion buildup on the 48V connector pins and BPCM pins. Two separate FCA STAR cases were opened by the dealer. The Power Pack Unit Battery was identified as the failed component. The dealer confirmed that the 48V cables required for repair are currently unavailable through Chrysler under any parts specifier, meaning FCA cannot supply the necessary parts to remedy this known defect. The vehicle has been inspected by an authorized FCA dealer on two separate occasions nine months apart, with the defect remaining unresolved on both visits due to FCA parts unavailability. Warning symptoms including low voltage codes and the P0A9C-00 fault code were first identified in June 2025, approximately three months before the highway stall event, indicating this was a progressive and worsening defect. The issue was first reported in June 2025 and remains unrepair
NHTSA complaint #11744009 — an unverified report by a vehicle owner.
Buda, TX
UNKNOWN OR OTHER
Went to start the jeep and the entire dash cluster was out. I had just gotten it serviced 2 days before it went out and there was no warning or indication that the cluster panel was damaged. Due to this issue I’m unable to see any speed, gas levels, signaling, oil level and any other signal indicators from the dash. This is extremely problematic and renders the vehicle unsafe to drive. It was inspected by the dealership and another mechanic and both parties confirmed the dash cluster was broken and needed to be replaced and that several other 2019-2020 jeep wranglers had been brought in with the same problem.
NHTSA complaint #11744023 — an unverified report by a vehicle owner.